- Home
- STS18ZBPRRWW
- Instructions
STS18ZBPRRWW General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Freezer not getting cold enough to freeze ice cream
8 of 10 people
found this instruction helpful.
-
Gary from ROSETO, PA
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers
I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the sma ... Read more ll challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing
Read less
Was this helpful?
Thank you for voting!
Freezer stopped working
9 of 13 people
found this instruction helpful.
-
Clifford from Melbourne, FL
- A Bit Difficult
- More than 2 hours
-
Nutdriver, Pliers, Screw drivers
I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into posi
... Read more
tion my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.
Read less
Was this helpful?
Thank you for voting!
Noisy fan in freezer compartment
6 of 6 people
found this instruction helpful.
-
Jeffrey B from Lewiston, ME
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed shelf by pushing to left and lifting up on RH end. Removed screws in plastic cooling tower and slid tower up. Pulled back wall of freezer compartment out, RH side first. Removed two screws from fan bracket, unplugged fan wiring harness by compressing connector spring clips and pulling joint apart. Pulled fan blade off (note locati
... Read more
on of blade on shaft for reinstall alignment purposes), removed both green grommets.Then just reinstalled new items.My philosphy on repairs of this nature is to replace all related parts that could be contributing to problem. The parts are cheap compared to the aggravation and inconvenience of doing the repair several times until you fix the problem. You don't need to purchase the compression ring if you buy the fan blade as it has one already installed on it. Problem solved, though now that the noise is gone am hearing fainter similar noises from lower fan. Should I be surprised, both fans are of similar design.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
no problem
7 of 10 people
found this instruction helpful.
-
hung from herndon, VA
- Really Easy
- 15 - 30 mins
-
Pliers, Screw drivers
The part i received fit perfect, i just removed the old part and put the new part in with the screw driver.Really easy
Other Parts Used:
Was this helpful?
Thank you for voting!
Door gasket was cracked and coming off
5 of 5 people
found this instruction helpful.
-
Mark from SALISBURY, MD
- Really Easy
- 15 - 30 mins
-
Socket set
Took freezer door off with torque screwdriver, unscrewed freezer door/refrigerator hinge with 3/8 socket. Removed refrigerator door and put on kitchen table. (Turn refrigerator off temporarily). Put freezer door back on temporarily. Pull out old gasket from groove on door. Put in new gasket. Take freezer door back off, put on refrigerator
... Read more
door, hinge, freezer door, put torque screws back in, your done. (Turn fridge back on)
Read less
Was this helpful?
Thank you for voting!
Refrigerator to warm
5 of 5 people
found this instruction helpful.
-
Lloyd from PITTSBURG, CA
- Easy
- 15 - 30 mins
-
Screw drivers
Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long
Was this helpful?
Thank you for voting!
light not working
7 of 11 people
found this instruction helpful.
-
robert from FRANKLIN SQ, NY
- Very Easy
- Less than 15 mins
-
Pliers, Screw drivers
I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.
Was this helpful?
Thank you for voting!
Plastic frame was broken
5 of 5 people
found this instruction helpful.
-
Sandra from YUMA, AZ
- Very Easy
- Less than 15 mins
I removed the broken frame, glass, and bins from the refrigerator, cleaned the area, put the new frame in place making sure it was fitted into the brackets securely, and replaced the glass and bins into their proper slots.
Was this helpful?
Thank you for voting!
A rat had chewed half of all four blades off
9 of 18 people
found this instruction helpful.
-
Curtis from Dothan, AL
- Really Easy
- Less than 15 mins
-
Nutdriver
First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut an ... Read more d checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut an ... Read more d checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.
Read less
Other Parts Used:
Was this helpful?
Thank you for voting!
The old plastic slide broke from hanging too much weight on it.
5 of 6 people
found this instruction helpful.
-
Terrence M from Portsmouth, NH
- Really Easy
- 15 - 30 mins
First I had to go to the hardware store to buy a star bit to remove the old screws ($1.09). I attached it to my quarter-inch drill and used it to remove the old screws. I then used those same screws to attach the new slide. Once I had the star bit, it was little more than a five-minute task.
Was this helpful?
Thank you for voting!
Broken part need to be replaced
4 of 4 people
found this instruction helpful.
-
ANGELINE from STAMFORD, CT
- Really Easy
- 30 - 60 mins
I didn't call for repair iwas just order 2 pcs it's coming early morning in the next day I was happy 1hundred% I will recommend this company
Was this helpful?
Thank you for voting!
The lights were on inside however the the water/ice dispenser did not work and the fridge and freezer side was not cooling
5 of 7 people
found this instruction helpful.
-
Rickey from DUMAS, AR
- Really Easy
- 30 - 60 mins
-
Socket set
Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugge
... Read more
d it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.
Read less
Was this helpful?
Thank you for voting!
refrigerator compartment too warm
4 of 5 people
found this instruction helpful.
-
samuel from windsor mill, MD
- Easy
- 15 - 30 mins
-
Nutdriver
Unplugged fridge and removed back panel inside freezer compartment . Unclipped defrost thermostat and snipped off with wire cutters . Installed new defrost thermostat with wire nuts , clipped back on , re-installed back panel , turned on fridge and within a couple hours food compartment began cooling down . Thermostat looks like a small m
... Read more
etal can clipped onto the heating coils with 2 wires attached . Also noticed excess ice build up on coils melted and drained into pan under fridge once unit started working .
Read less
Was this helpful?
Thank you for voting!
Difficulty in removing the old switch
5 of 8 people
found this instruction helpful.
-
James from Federal Way, AL
- A Bit Difficult
- 30 - 60 mins
-
Screw drivers, Socket set
The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around.
... Read more
If i had ordered the replacement before and not afterwards I would have seen this before hand.
Read less
Was this helpful?
Thank you for voting!
Refrigerator light wouldn't come on.
4 of 5 people
found this instruction helpful.
-
Daniel from Crown Point, IN
- Easy
- 15 - 30 mins
-
Pliers, Screw drivers
After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.
Was this helpful?
Thank you for voting!