SSL27RGRCBS General Electric Refrigerator - Parts

This ice and water filter helps reduce impurities in select side by side and bottom freezer refrigerators. Replace it about every six months, or when water flow slows, ice production drops, or the filter light turns red. Some older filter setups may need an adapter. Place a cloth under the filter before removal. Check the exact refrigerator model before ordering.

This temperature sensor, also called a thermistor, measures temperature inside the refrigerator or freezer and sends readings to the main control board. The board uses this information to control cooling, including compressor and fan operation. Incorrect readings may cause the compartment to become too warm or too cold, or make cooling ru...Read moren longer than needed. The replacement includes the sensor body and wire leads. Its location varies by appliance. This is an OEM part sourced directly from the manufacturer.

This defrost termination thermostat (Defrost Limiter Thermostat, High Limit Thermostat, Refrigerator Defrost Bi-Metal Thermostat) acts as a safety device to stop the evaporator coil from overheating, by turning off the defrost heater at the end of the defrost cycle. This part attaches to the tubing of the evaporator coil in the freezer. A...Read more faulty defrost termination thermostat may result in the defrost heater never heating and a solid frost buildup on the evaporator coil, which results in too warm temperatures. The thermostat contacts are normally closed and have continuity until it reaches 140 degrees. If this high limit thermostat is open at room temperature or colder, it is defective. This limit thermostat has an attached mounting clip and comes with pink and amber wire leads. The thermostat is 1 inch in diameter and 1/2 inch thick, the 2 wire leads are 10 inches long.

If your refrigerator is leaking, the dispenser is not dispensing, or the ice maker is not making or dispensing ice, the inlet valve may be involved. It controls water flow to the refrigerator’s water system and includes a guard. Check water pressure first; if it is sufficient, test valve continuity with a multimeter. Disconnect power befo...Read morere testing or replacing the valve. The inlet uses a 1/4-inch compression fitting, with 1/4-inch and 5/16-inch John Guest outlets. Confirm fit for your refrigerator.

The Module Shelf Insert is a complete assembly for the module shelf. This repair is rated as "Easy" by users. Simply remove the old shelf insert and snap the new one into place using the locking tabs. This part is used to hold items in the fridge, and if broken it should be replaced. Refer to your user manual and model number to ensure this part is right for you.

This refrigerator ice maker assembly automatically freezes water and releases crescent-shaped ice cubes into the storage bin. It replaces an existing ice maker that has stopped cycling, fails to release ice, or has damaged components. Poor ice production can also result from a restricted water supply or incorrect freezer temperature, so c...Read moreheck these conditions before replacing the assembly. Confirm the mounting arrangement, fill cup position, electrical connections, and included adapters against the appliance parts list to ensure the kit matches the original installation. This is an OEM part sourced directly from the manufacturer.

Warm, moist air stays out of the ice chute when this refrigerator dispenser door flapper closes against the opening. The flap opens during ice dispensing, allowing cubes to pass through, then returns to form a seal when dispensing ends. A cracked, warped, or damaged sealing edge may leave gaps that contribute to frost, condensation, or dr...Read moreipping around the chute. Replacing a damaged flapper helps restore proper closure and reduces air leakage between the freezer and room while the dispenser is idle. This is an OEM part sourced directly from the manufacturer.

This red evaporator fan grommet cushions the fan motor where it meets the mounting bracket inside the freezer. It measures approximately 1 inch in diameter and helps reduce vibration transferred from the running motor. Wear, tears, or damage may contribute to buzzing or rattling from the fan area. Inspect the grommet, bracket, and fan bla...Read morede before replacement, since loose parts or blade contact can cause similar noise. The grommet sits behind the evaporator fan cover. Disconnect power before accessing the assembly and follow the mounting instructions for correct placement. This is an OEM part sourced directly from the manufacturer.

This ice dispenser solenoid moves the linkage that opens the ice chute door when dispensing is activated. When power is released, the mechanism allows the flap to close and limit warm air entering the freezer. A failed or sticking solenoid may prevent ice from dispensing or leave the chute door open, contributing to frost or moisture buil...Read moredup. Inspect the solenoid, spring, and door linkage before replacement, since other mechanism faults can cause similar symptoms. Disconnect power before accessing the dispenser assembly and follow the appliance instructions for mounting and wiring. This is an OEM part sourced directly from the manufacturer.

This electronic board (Main Control Board Assembly, Control Board, Motherboard) controls the temperature and defrost functions of the unit. This control board is located on the back of the refrigerator, and measures 8 inches by 5 inches. It’s constructed of metal and plastic, and comes in green. This kit includes one main control board wi...Read moreth built in defrost controls. If broken due to electrical surges or normal use, your fridge may experience temperatures that are too warm or too cold, or inconsistent defrost cycles. If this happens, the part should be replaced.

This defrost heater and bracket assembly melts frost from the evaporator coils during the automatic defrost cycle. Clearing the frost allows air to move across the cooling surface and through the refrigerator compartments. A failed heater may allow ice to build up, restricting airflow and leaving the fresh food or freezer section too warm...Read more. The appliance may also run longer without reaching the set temperature. Confirm the heater fault before replacement, since the thermostat and defrost control can cause similar symptoms. Disconnect power before accessing the assembly. This is an OEM part sourced directly from the manufacturer.

This part is found at the end of the auger in the ice container - replace this part when the icemaker doesn't dispense ice.