EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details
✖

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

SRM-2400SB Echo Trimmer - Overview

Models starting with SRM-2400SB

Enter a part description. DIY Heroes keep it simple, eg. "belt" or "pump".

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Trimmer Fuel Grommet – Part Number: 13211546730
$6.40
In Stock
Trimmer Fuel Grommet
★★★★★
★★★★★
(7)
Part #13211546730
This is a genuine ECHO/Shindaiwa replacement part It is compatible with over 150 machines listed below. The Fuel Line Grommet is placed into the fuel tank. The Vent tube, Fuel return line and fuel line are inserted through the three holes. A worn Fuel Line Grommet will cause fuel to leak from the tank. When replacing the Grommet it is advisable to replace the fuel lines at the the same time.
Fuel Filter – Part Number: A369000480
$7.73
In Stock
Fuel Filter
★★★★★
★★★★★
(2)
Part #A369000480
This OEM Fuel Filter is a silver and white, steel/felt, part measuring about 1.25 inches in length and 3/4 inch wide. It can be installed with pliers and is rated as Easy to install by customers. This part attaches inside the fuel tank to clean the fuel of debris, and should be replaced during regular maintenance, check your manual for recommended replacement time. If the filter is leaking or it has a blockage preventing fuel flow, then it should be replaced. If the engine sounds like it is not getting enough fuel, then remove the filter and check it for blockage.
Purge Bulb – Part Number: 12318140630
$6.88
In Stock
Purge Bulb
Part #12318140630
The Primer Pump, aka the Pump Bulb, is a clear, individually sold, plastic part, sourced from the original equipment manufacturer. It has an Outer Diameter of 0.616 Inches, 15.66mm and is 0.558 Inches and 14.19mm in height. This part is used to pump fuel from the tank to the carburator and is rated Easy to install. This part installs onto the primer assembly. If the part dries out or starts leaking that means it is broken (likely due to fatigue or general wear) and must be replaced. Check the model number to ensure you are choosing the right part.
Trimmer Fuel Return Tube – Part Number: 13201056330
$6.40
In Stock
Trimmer Fuel Return Tube
Part #13201056330
The fuel return tube or fuel return line, as it is also known, delivers fuel back to the tank from the primer bulb. This is a genuine OEM part from the manufacturer, and it is yellow in color and sold individually. Its overall dimensions are 3x6x90mm. Over time, or due to over-tightening, cracks may appear in your fuel return tube, causing fuel to leak. You will know it is time to replace this part if you notice these symptoms. This is an easy repair, according to our customers, and does not require any special tools. The new part will simply attach to the primer bulb and fuel tank.
Leaf Blower Fuel Tank Vent – Part Number: A356000031
$10.97
In Stock
Leaf Blower Fuel Tank Vent
★★★★★
★★★★★
(1)
Part #A356000031
This a a genuine OEM replacement check valve for your small engine. It is also known as a fuel tank vent. You may need to replace this part if you are noticing debris or dirty oil in the reservoir. Make sure the engine is cool before you begin this repair, and remove the wire and boot from the spark plug to prevent the engine from starting up.
Vent Tube – Part Number: V471001200
$6.40
In Stock
Vent Tube
★★★★★
★★★★★
(2)
Part #V471001200
This is the replacement vent tube for your outdoor power equipment. It is made of black plastic and is approximately 3 inches long and ¼ inch thick. The vent tube allows air into the fuel tank so that a vacuum is not created when fuel is being fed through the fuel line. The vent tube is often connected to the fuel line grommet that is installed on the fuel tank. If the vent tube is broken or missing, it can lead to decreased engine power and performance. This part is sold individually and is an authentic OEM part sourced directly from the manufacturer.
Air Filter – Part Number: 13031051830
$10.01
In Stock
Air Filter
Part #13031051830
Genuine Echo Replacement part, this item is sold individually. The 13031051830 Air Filter is used to keep dust and debris from contaminating the carburetor and engine. This filter is used on all the Echo Outdoor Products listed below. When this Filter gets clogged and dirty it will diminish the performance of the engine. It should be replaced at this time.
Throttle Trigger – Part Number: 17801052130
$6.40
In Stock
Throttle Trigger
★★★★★
★★★★★
(2)
Part #17801052130
This is an OEM replacement part, it is sold individually. The Throttle Trigger controls the speed of the engine of the models listed below. The throttle cable connects to the trigger, then down to the throttle lever on the carburetor. Because of its constant use the Throttle Trigger has a tendency to break or wear out.
Intake Gasket – Part Number: V103001360
$6.40
In Stock
Intake Gasket
Part #V103001360
This is a genuine manufacturer approved replacement part designed for use with edgers and trimmers. The purpose of this part is to act as a seal for the insulator. This item is made out of compound material and it is sold individually. To complete this repair you would need a screwdriver.
Spark Plug-Bpm-7Y – Part Number: 99944500071
No Longer Available
Spark Plug-Bpm-7Y
Part #99944500071
This spark plug is sourced from the original equipment manufacturer. It is a small device in the engine cylinder head which is responsible for creating the spark that ignites the fuel in the engine and allows the engine to run. The spark plug comes in a cylindrical shape and is wrapped in a ceramic/porcelain insulator. It has a metal rod, known as the center electrode in the center and a metal tab at its base, known as the ground electrode. The spark plug may fail due to a buildup of carbon, physical damage, or fouling. To confirm that the spark plug is faulty, visually inspect it and use either a multimeter set to continuity or a spark tester to test the spark plug for electrical failure. Unthread the faulty spark plug using a spark plug socket and ratchet. Use a spark plug gap tool to set the correct gap and finally, carefully thread the new spark plug into the engine. Regularly inspect and replace your spark plug as part of your general maintenance to keep your equipment in good condition.
Spark Arrester Screen – Part Number: 14586240630
$6.40
In Stock
Spark Arrester Screen
Part #14586240630
Also referred to as a Spark Arrester, this Spark Arrester Screen is an authentic OEM replacement part that is not part of a kit or assembly. It is made of metal and sold individually. The purpose of this screen is to prevent flammable debris from entering the engine and becomes worn through regular use. If the screen is clogged, remove the screen from the muffler, hold it with pliers, and use a torch to burn off the debris before reinstalling the screen. This part needs to be replaced when it becomes damaged or worn. When the screen is malfunctioning, you may notice debris exiting through the muffler. To complete this repair, you will need a screwdriver and pliers. This screen is located within the muffler; refer to your owner's manual for the exact location on your model. Customers rated this repair as Easy.
Trimmer Air Cleaner Case Assembly – Part Number: P021002921
$17.35
In Stock
Trimmer Air Cleaner Case Assembly
Part #P021002921
This air cleaner case assembly is an OEM replacement housing designed to hold and secure the air filter on gasoline-powered outdoor equipment. Made from durable plastic, it helps keep dirt and debris out of the intake system, ensuring a clean air-to-fuel mixture for reliable engine performance. It is an ideal replacement when the original air filter housing is cracked, loose, or no longer sealing properly, helping reduce premature filter clogging and engine wear.

Watch our pros, then fix it yourself.

See how others fixed this model. Time, tools, difficulty, and steps that lead to victory! View More

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
Echo trimmer had narrow shield. Bought wider one which reduced rocks and debris
5 of 9 people found this instruction helpful.
  • Robert from COEUR D ALENE, ID
  • Very Easy
  • Less than 15 mins
  • Screw drivers
Easiest repair ever. Turn the trimmer upside down so you can access the string assembly. Find the small hole in the shaft beneath the string assembly and insert a heavy gauge nail into it to hold the shat in place. Turn the string assembly counterclockwise until it comes off. Lift off the round metal piece that was under the string assemb ly.Find the 3 screws holding the shield in place and unscrew them. Pull the shield off. Install the new one in reverse order. I used the original hex screws as the new ones were philips head. Hex worked perfectly. I was amazed how easy thus was to do.
Was this helpful?
Thank you for voting!
Replacing grommet that holds the fuel tubes
4 of 7 people found this instruction helpful.
  • Stephen from NAPERVILLE, IL
  • Really Easy
  • 30 - 60 mins
  • Screw drivers
Any DIYer can do this. Don’t hesitate.
Was this helpful?
Thank you for voting!
Original cylinder was cracking apart on my Echo weedeater
1 person found this instruction helpful.
  • Leonor from SHARPSBURG, MD
  • Really Easy
  • Less than 15 mins
  • Socket set
Bought a new cylinder cover and bolted it on. Was easy.
Was this helpful?
Thank you for voting!