SNS45 (582003N) Senco Nailer - Parts

This is a genuine Senco replacement part, it is sold individually. Its purpose is to retain or secure the Retaining Pins in the Senco models below. It is attached to the pins by pressing them on the beveled end of the pins.

This is a Genuine OEM replacement part for use with Senco Nailers/Staplers. This item is made out of Rubber Material and it is Sold Individually. The purpose of this part is to create a seal so air does not leak from the gun. When replacing this Seal it is advised to inspect all of the other Seals and O-Rings for wear. When replacing this item you would need an Allen Wrench Set and Pliers.

This is a manufacturer sourced replacement part designed for use with Senco staplers. This is one of the seals for the valve. Over time it will shrink, become brittle and crack allowing for air leaks. At that time it should be replaced. It is made out of rubber material and it is sold individually. Replacing this item you would need hex key/allen wrench and pliers to replace this item.

This is an authentic replacement part manufactured for use with Senco pneumatic nailers and staplers. The special spring is commonly used to provide resistance for the single sequential type of trigger assembly. This spring is available as an individual replacement part.

This spring is an OEM part direct from Senco. The metal spring is compatible with several nailer devices, and is sold individually. This component provides the necessary resistance in the trigger. Pliers and a hex key are often required for the installation.

This authentic item is sourced directly from the original equipment manufacturer for use with Senco framing nailers. It is one of the special pins utilized to secure the cover for the trigger. The pin fits into the housing and is secured in place by a retainer which is sold separately. It provides a high-quality replacement for a missing ...Read moreor a damaged component that was installed on a new unit. To ensure the correct installation, refer to the appropriate diagram of your model. You will need pliers to remove and secure this hardware. NOte, one durable metal pin is included.

This is an Authentic OEM replacement part for use with Senco Nailers/Staplers. This item is made out of Rubber and it is Sold Individually. The purpose of this part is to create a seal so air does not leak from the gun. When replacing this Seal it is advised to inspect all of the other Seals and O-Rings for wear. When replacing this item you would need an Allen Wrench Set and Pliers.

This replacement seal O-ring helps maintain an airtight seal within pneumatic nailers and staplers, ensuring consistent air pressure and reliable tool performance. Manufactured from durable rubber, it is designed to prevent air leaks within the tool's internal air system, helping restore proper driving power and operating efficiency when ...Read morethe original O-ring becomes worn, cracked, flattened, or damaged. Common symptoms of a failed seal include reduced fastening power, air leakage from the tool body, and inconsistent operation. Installation typically involves disassembling the affected portion of the tool, removing the worn O-ring, lightly lubricating the new seal with pneumatic tool oil, and installing it in the original groove before reassembly. Weighing approximately 0.01 lbs, this small but essential maintenance component helps extend tool life and maintain dependable performance. For best results, inspect related O-rings, seals, and cylinder components during servicing and replace any worn parts as needed to ensure a complete and long-lasting repair.

This is a genuine manufacturer-sourced component which is specially made for Senco staplers. It is an identical replacement for a missing or a faulty part that was installed on a new unit. The purpose of this component is to provide a tight seal between connected pieces. Please make sure to refer to the appropriate diagrams of your model ...Read morefor the correct location and application of this seal. Keep in mind this high-quality item is made of durable rubber and is sold individually.

This is an authentic manufacturer-sourced replacement part which is specially designed for use with Senco staplers. The purpose of this component is to provide a tight seal between connected parts, please make sure to check the appropriate diagrams of your model for the correct location and application of this hardware. Keep in mind this high-quality item is made of durable rubber and is sold individually.