SN62 - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This manufacturer-approved screw is for refrigerators, including Kenmore refrigerator model. Avoid cross-threading refrigerator screw during installation.

This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material ...Read moreand it is sold individually. You would need a set of wrenches to complete this repair.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

It is an authentic OEM part which is specially designed for Murray, Snapper and Simplicity snowblowers. This bearing secures and stabilizes moving parts to ensure proper rotation angle and position. Unfortunately, over time the components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-qualit...Read morey item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

This temperature sensor (part number DA32-10105T) is for refrigerators. Temperature sensor DA32-10105T senses the temperature inside the refrigerator and sends information to the electronic control. Unplug the refrigerator and safely store any food that could deteriorate while the power is off before installing this part. Wear work gloves to protect your hands.

This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before...Read more installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.