SN624 ((6240810x110-18-2827-88)(2007)) Murray Snow Blower - Overview

This ball bearing is sourced from the original equipment manufacturer and can be used in a variety of outdoor equipment. It has an inner diameter of 11/16 inches. The ball bearing provides support for the rotating parts in your equipment and reduces the amount of friction they are subject to during use. If the bearing is not adequately lu...Read morebricated or has worn down, you may hear grinding or squeaking from your equipment and notice excessive vibration when in use. It is important to address this issue promptly as a faulty ball bearing can potentially damage the parts located near it. To replace the ball bearing, use a pry bar or bearing puller to pry it out of its housing. Clean the housing thoroughly and press your new ball bearing in position. Note that when pressing the ball bearing into place, apply force only to the outer portion of the bearing.

This is an authentic OEM sourced driver belt, not an aftermarket equivalent. It is specially designed for a variety of snow throwers. This is the main drive belt for the unit that will spin the augers. Please make sure to check appropriate diagrams for correct location and application of this item. It is made from durable rubber material ...Read moreand it is sold individually. You would need a set of wrenches to complete this repair.

This hex nut is a fastener made from steel and is used to secure the end of a bolt in various lawn and garden equipment and machinery. It is a genuine OEM replacement part that comes in a standard size of 5/16 of an inch with 18 threads per inch. The hex nut has a hexagonal shape, which gives it greater grip and makes it easy to tighten u...Read moresing a wrench or a set of pliers. The nut also has a flange on one end, which locks the nut in place, prevents damage to the area where it is installed, and allows the load to be evenly distributed. It is important to replace your hex nut if it is loose, cracked, or corroded. If you have not yet removed the old hex nut from your equipment you will need a socket wrench to remove it. After that, you can easily install the new nut by threading it onto a bolt or screw and then tightening it with a wrench or pliers until it is tightly secured.

The hair pin is a silver, metal pin used to secure and lock parts in place. If broken, the part being secured will come loose and the pin should be replaced. This is an OEM part directly from the manufacturer. Most customers rated the replacement of the hair pin as an easy repair.

It is an authentic OEM part which is specially designed for Murray, Snapper and Simplicity snowblowers. This bearing secures and stabilizes moving parts to ensure proper rotation angle and position. Unfortunately, over time the components will wear out and may begin to fail eventually requiring a replacement. Keep in mind this high-qualit...Read morey item is made of durable metal and is sold individually. Please make sure to refer to the appropriate diagrams of your model for the correct location and application of this hardware.

This is an original part from Craftsman for use with Craftsman Snowblowers. The fiction wheel assembly meshes with the friction disc, causing the drive wheel axle to turn. The most common reason for replacing the friction wheel is when the snowblower's wheels don't turn.This part is sold individually. Disconnect the spark plug wire before...Read more installing this part. The tools that you will need to replace the friction wheel disc are 3/8" socket, 9/16" socket, adjustable wrench, hammer, 1/2" socket, flat-head screwdriver, and lubrication.

This flat washer is an OEM part that is silver in color, made of metal, and its job in your equipment is to spread load and pressure under a bolt. It can have multiple uses depending on your equipment, and can be used in a lot of different equipment, so be sure to consult your owners manual or check your part number to ensure this fits yo...Read moreur model. Over time the washer may become damaged; watch for cupping from over-tightening as a leading cause. This is a very easy part to repair and does not require any tools.

This is an original replacement part manufactured for use with Craftsman snow throwers. The special bolt is used to secure the auger blade to the axle. The bolt is used as a safeguard if the blade gets caught or stuck the force will snap the bolt rather than breaking more expensive parts like the auger transmission. The bolts are sold in ...Read morepairs and include the nuts and washers, the bolt sets are sold as individual sets.

This genuine item is supplied by the original equipment manufacturer for use with Murray, Simplicity and Snapper lawn mowers. It is the special retaining ring for the wheel. If the hardware is missing or is damaged, this will provide an identical replacement for the original part that was installed on a new unit. One durable metal retaini...Read moreng ring is included. Make sure to check the appropriate diagrams for your model to ensure the correct repair procedure.

This is available as an individual replacement part. The auger bearing connects to the auger plate and is made of plastic. If this part becomes broken it will need to be replaced and may require a screwdriver during the installation. It is an OEM Craftsman part directly sourced from the manufacturer for use in snowblowers.

This quarter-inch Nylock nut, or hex nut, is silver in color and sold individually. Made of metal, its simple task is to secure and lock parts in place on a variety of different equipment. Regardless of the specific function, this nut may become damaged over time and if you notice the part it is securing becoming loose, it is time to chan...Read morege the Nylock Nut. Use a wrench to make this repair, ensuring your torque to the manufacturer specs. Most of our customers found this to be an easy repair, but difficulty can vary depending on the part you are accessing to make the repair.

This hex locknut has a special locking feature to prevent it from loosening due to vibrations or movement. It has a 1/4 inch diameter and a 20 threads-per-inch pitch. You will find it securing various parts of your lawn equipment, such as blade assemblies, engine mounts, or handles. A broken locknut cannot fasten components together tight...Read morely. Replace any damaged locknuts to keep your machine securely assembled and functioning properly. Loosen a locknut from your machine by turning it with a wrench or a socket. This durable metal locknut is an OEM hardware. It is sold individually, so read your user manual to determine how many you will need. Consider getting extras if you are replacing one, as these locknuts tend to wear out together.