S-2P Echo Trimmer - Parts

The m10 Left Hand Thread Nut is a 10mm, gold metal part, sold individually. This nut is a "reverse thread". It requires a wrench or socket set to install, and installation is rated as "Easy". Use this part to secure the blade to the unit, by attaching it to the shaft, securing the cutting blade. If broken or damaged, it should be replaced...Read more. Refer to your make, model and diagrams to check if this is the right part for you.

The Cotter Pin (or Split Pin) is a 2x22mm silver metal part, sold individually. It is rated as "Easy" to install, and installation will require a set of pliers. It can be attached in various locations on a variety of equipment and is used to secure and lock parts in place. If broken, damaged, or worn down the part it is securing may becom...Read moree loose, and the part should be replaced. If this part is removed for repairs, replace it with a new one. Refer to your make, model, and diagrams to make sure this is the correct part.

This piston ring is an authentic manufacturer approved replacement part. Is is commonly used on Echo gas trimmers/edgers. The purpose of a piston ring is to create an air tight seal inside the cylinder. A worn or broken piston ring will allow combustion gases to escape the seal and enter the crankcase. This would cause low compression and...Read more a loss of power. Replacing an o-ring should resolve this issue. This part is made out of metal and is sold individually. To complete this repair you will need a set of wrenches, pliers and a screwdriver. • Remove the air cleaner • Drain the fuel • Remove the air cleaner case • Remove the carburetor • Remove the intake insulator • Remove the spark plug • Remove the engine cover • Remove the insulator gasket • Remove the starter assembly • Remove the fuel tank • Remove the air duct • Separate the engine • Bind the engine • Remove the clutch • Remove the flywheel • Remove the starter pulley • Unbind the engine • Remove the muffler • Separate the cylinder from the crankcase • Remove the piston ring • Install the piston ring • Reassemble and test the equipment

This OEM nut is a 5mm, gold, metal nut, which is sold individually. It can be installed with a Wrench or Socket and Torque Wrench by torquing to the manufacturer specifications. This nut is used to secure another part in place, and should be replaced if damaged due to fatigue (such as damaged threads or rounded ends). This nut can have v...Read morearious uses on various equipment, and as such the difficulty of the installation can vary, but generally this is an easy repair.

This spark plug wire, also known as a spark plug coil or spark plug cap coil, is compatible with various makes and models of hand-held outdoor power equipment and is sold individually. This wire is installed within the spark plug boot and attaches to the spark plug for the ignition of your equipment. The spark plug wire is often exposed t...Read moreo extreme heat and excessive vibrations, so through normal wear and tear, it will likely break down. If your equipment is having difficulty starting or has general performance issues, the wire may be the reason why. To replace this wire, make sure your equipment is off before removing the wire and boot from the spark plug. Remove the boot from the wire and install the new wire within the boot before re-installing the boot back to the spark plug.

This replacement spark plug cap is a genuine OEM sourced item designed for use on handheld lawn and garden equipment. It is used to insulate the plug and wire terminal. Over time rubber material can dry out and crack requiring replacement. Please note, this item is sold individually.

The Blade Fixture is a silver, metal, individualy sold blade, which attaches at the bottom of the cutting head assembly, being held on by the nut and cotter pin. It is used to secure the blade fixing plate of the trimming tool. Installation is rated as "Easy" and requires a wrench and pliers to complete. If broken or damaged due to genera...Read morel wear, the cutting blade will not be secured, may be loose, or may not be able to stay on, which means you need to replace it. Refer to your make, model, and diagrams to ensure this is the correct part.

This is an original Echo replacement part manufactured for use with outdoor power equipment. This special screw includes a washer and can be used with either flat or phillips head drivers. The screw has different applications, please see model diagram for part location and use. The screw is sold individually.

It is a genuine OEM approved replacement item specially designed for use with Echo gas powered handheld tools. This replacement fuel-strainer/filter fits inside of the fuel tank. The purpose of this item is to filter out dirt and debris from contaminating engines. Over time fuel filter will get clogged and restrict the fuel getting to the...Read more carburetor. At this point filter should be replaced. This filter consists of a metal body with fabric filter material and it is sold individually.

This is an authentic replacement part manufactured for use with Echo backpack blowers, edgers, and trimmers. The screw has multiple applications that vary depending on the model of equipment. This screw is sold individually, please see model diagram for part location and usage.

This replacement spark plug is an authentic OEM sourced item, not an aftermarket imitation. It is commonly utilized on Echo gas powered lawn and garden equipment. A spark plug delivers electric current from an ignition system to an internal combustion engine. Over time spark plugs will become dirty or fouled requiring replacement. Please ...Read morenote, one item is sold individually. Replacing a spark plug you will need a spark plug wrench or a socket wrench.