RY74003D Ryobi Chainsaw - Parts

This is an adjusting pin kit, also known as a chain tensioner kit, for various chainsaw models. This genuine OEM kit features an adjustment/tensioner pin and bar adjustment screw to modify and change the tension of the chain, so when the chain becomes loose over time, you can tighten or loosen it depending on your needs. If the chain for ...Read moreyour chainsaw becomes too loose, it can come off the bar and cause injury, but if too tight can damage the bar or engine of the chainsaw. This assembly is installed on or near the clutch assembly of the chainsaw and is usually accessible by removing an access panel. Replacing this assembly is easy and only requires a wrench and screwdriver. First, disengage the chain brake and remove the screws securing the side panel of your chainsaw. Remove the side panel and locate the bar adjustment screw. Loosen the old adjustment screw and remove it and the tensioner pin. Thread the new adjustment screw through the new tensioner pin until the screw is locked into place. Then rotate the screw counterclockwise until the pin is in the middle of the screw. Replace the cover panel assembly and test the chainsaw.

This high quality replacement chain is specially designed for use with Homelite and Ryobi chainsaws. It is a genuine OEM sourced item, not an aftermarket imitation. This chain is only for use with 14" bars only. Over time chains tend to stretch and become dull requiring replacement. Please note, this metal chain is sold individually. To ...Read morereplace this chain you will need a wrench set and a screwdriver. • Remove the guide bar side panel • Release the chain tension • Remove the old chain • Loosen the tension screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts

This is a Manufacturer Sourced replacement part for Lawn and Garden equipment. This item is Metal an is Sold Individually. A lock nut is a type of nut that resists loosening when properly threaded onto a bolt. This Locking Nut has multiple uses based on your tool. You would need a Wrench to tighten or loosen this Hex Nut.

Genuine OEM replacement part, this item is sold individually. The purpose of the 631036001 Guide Bar Plate is to assist in keeping the Chainsaw Blade inline. Also with out this plate, if the chain was to come of the chain bar, this part would help keep the housing of the Chainsaw from being damaged.

Ergo grip starter handle

Genuine OEM replacement part, this item is sold individually. This is part of the Guide bar adjustment kit. The chain bar is sandwiched between this part and part number 631036001 Guide Bar Plate. You can obtain the complete Guide Bar Adjust Kit, by ordering part number UP06966A.

Authentic manufacturer approved replacement bolt made for use with string trimmers and chainsaws. This is a standard hardware with multiple uses based on your tool. Please refer to specific diagrams for correct application. This bolt has a hex socket head which requires a hex key/allen wrench for installation. It is sold individually.

This rope is part of the pull starter system on Homelite and Ryobi gas powered lawn and garden equipment. It is an authentic manufacturer sourced replacement part, not an aftermarket equivalent. When the rope is pulled to start the engine, it is returned back into the starter pulley by means of the starter spring which is sold separately....Read more Please note, this rope is made out of strong fabric and it is sold individually. Replacing this starter rope you will need a screwdriver. • Remove the housing-cover • Remove the carburetor • Disconnect the clutch housing • Bind the engine • Remove the clutch drum • Remove the clutch • Remove the starter • Remove the starter handle • Remove the recoil pulley • Remove the old rope • Install the new starter rope • Reassemble and test the unit

This is an authentic replacement screw which is supplied by the original equipment manufacturer for use with handheld lawn and garden equipment. It is a standard hardware which has multiple applications depending on the model of your unit, please make sure to check appropriate diagrams for correct location and use of this item. This high-quality Torx screw is made of durable metal and it is sold individually.

This replacement ignition coil also known as a magneto is a genuine OEM part. It is specially produced for Homelite and Ryobi chainsaws. It plays an important role, because it producing pulses of high voltage for the spark plugs. It is made out of metal with a rubber insulated wire and a spark plug boot. Please note replacing this module...Read more would differ based on your unit, however the basic steps would be the same. To complete this repair you will need screwdriver and a wrench set. • Remove the housing/covers from the unit • Remove the spark plug • Bind the cylinder • Remove the air filter cover and side cover • Remove the throttle cable from the carburetor • Disconnect the wires • Remove old ignition coil • Install new ignition coil • Set the gap • Reassemble and test the unit