RVM1435BD001 Hotpoint Microwave - Instructions

Turned out the issue was easily solved by replacing a single, inexpensive fuse.

First off, UNPLUG THE MICROWAVE.

The fuse is located under the plastic grill at the top of the microwave. It's held on by two screws. Once you've removed the screws and taken off the plastic grill, you go to the right side of the mic ... Read more rowave and remove another screw that holds a small metal grill in place. Removing the small metal grill is probably the toughest part of this repair. You kind of have to rock it back and forth a bit to get it to release. Once that's off, you can get to the fuse. I removed the burnt out one with a pair of needle nose pliers. I also put a small piece of cardboard under the fuse when I did this so I didn't accidentally drop it into the innards of the microwave. I did the same thing when I replaced the new fuse. I then plugged the appliance back in and made sure it worked. Once that was confirmed, I replaced both grills.

The unbelievable happened. Our glass carousel cooking tray developed a crack. Each day the crack got longer. I ordered a new one on Tuesday and it arrived the next morning just before the cracked one completely cracked. I have never experienced such fast service. I highly recommend PartSelect and their helpful service.

replaced the plate

Above the stove mounted microwave. I dropped the lens cover from under the bulb and tried to remove the bulb. The bulb separated from the base. I tried to remove the base with a pliers and the lamp socket broke. I ordered the parts and dropped the bottom cover of the unit down (5 screws). Removed 1 screww from the lamp socket, unplugged t ... Read more he wires and took it out. Simply replaced socket, fastened bottom cover of microwave, installed new bulb and closed lens cover.

First I unplugged the microwave. :) Then, I removed the 6 screws found underneath the microwave, which allowed the bottom piece to hang down so I could see the turntable motor. I took the two screws out holding the motor in place and pulled the electric connectors off the motor terminals. Then I got the new part from PartSelect.com, repla ... Read more ced the electrical commectors, fit the motor back into the slot it came from (cause the pin has to be seated up in the hole) and replaced the 2 screws holding in the motor. Then I put the bottom metal piece back up and put the 6 screws back in. It was really easy - and I'm a chick! ;)

I ordered the part and when I recieved it, I saw that I had orderd the wrong size. I called and customer service was very friendly and helped me to get the correct part. they sent the new part out and even though it was christmas hollidays I recieved it the day after Christmas. Great Company

I went on line and tped in GE your web site came up. It didn't even take 5 minutes to order the part. The best part was I ordered it on Sunday and when I got home from work that Tuesday it was at my front door. I will certainly use your company again.
Thank You

Opened the box and put the new tray in the micro wave. Drank a beer and made microwave popcorn. The End!

At first I tried to use pliers to unscrew the base,very uncomfortable working position,upside down and backwards(the microwave is installed over the range top)very limited space for your body and arms to manuver and you really cant see the base,all of this took place after the breaker was turned off ofcourse,finally figured out that you c ... Read more an drop the entire bottom housing of the microwave by unscrewing 6 screws and the light sockets are easily accessable once you lower it,take out 1 retaining screw ,remove the entire socket and unscrewed the broken base and replaced the bulbs,I said bulbs,there is no sense in having to replace another bulb in who knows how long since only one had burned out but they were both the same age

Had to take unit off wall and disassemble the main casing.then disconnected the wires from the magnetron.took the mounting nuts off but wasn't able to remove the magnetron until I loosened the transformer out of the way .Then it came out easy.Installed the magnetron ,tightened the nuts,installed the transformer back in, connected the t ... Read more he wires back on and installed the casing on ,screwed the screws and got help to install the unit to the wall again.....Tested the unit before putting back on the wall to make sure it heated....The parts were exac same type and wasn't too hard to do...

i had to replace the cooking tray after 9 yrs as i dropped it and broke it. i ordered the new tray in feb and rec'd it right away. the new tray mysteriously burst one day in the microwave after a few weeks. i spoke w someone at partselect and they replaced it right away. wonderful customer service. thank you.

Unscrewed bottom plate of microwave and two screws that secured motor. Disconnect wires. Reversed process when installing new motor. Couldn't have been easier.

put cooking tray in place

We were so happy to be able to order a replacement glass microwave tray after I broke ours during cleaning. In this throw-away world we live in, we assumed we would just have to buy a new microwave but ours was only two years old so we really didn't want to do that. We found the same microwave at the store but it had gone up in price qu ... Read more ite a bit. Ordering this plate as a replacement part just made financial sense, and it was so easy to order. It arrived very quickly and we were extremely pleased with the whole experience.

The tray drive motor arrived quickly. I opened the package and made sure the correct motor arrived. I shut off the power to the microwave/exhaust hood. Then I grabbed a screwdriver and dropped 5 screws from the bottom of the microwave. I then removed 2 more screws that hold the motor in place. Unplugged the 21 volt power clips. Placed th ... Read more e new motor in position and replaced the screws and attatched the power clips. I then placed the bottom pan in position and replaced the 5 screws that hold it to the bottom of the microwave. Turned the microwave on and it worked properly! The total cost was $40 and I probably saved more than a hundred dollars on a service call. What a happy ending and it took about 5 minutes to perform the repair! Thanks PartSelect. You are the best!