RUD4000MU0 Roper Dishwasher - Instructions

Removed dishwasher lower faceplate.
Removed hose clamp at the dishwasher end.
Removed clamp at the garbage-disposal end.
Removed hose.
Pulled new hose.
Connected both ends of the hose.
Installed both clamps.
Tested.

Look at the exploded parts diagram, that parts select provides on their website.

You have to take off the nine star pointed screws. So you need a special screwdriver or I had a socket set of them and I used a ratchet to make it easier. I think there are nine of them around the base of the door. Then remove the door and set it o ... Read more n the counter. Flip it over and there is a small plastic cover that has to be removed from the back of it, and it is easily removed by gently pulling on it.

Now comes the difficult part. There is a locking piece on it that holds the latch onto the door by interlocking with a piece on the back side of the door. I took a pair of wire snips and just cut the old interlocking piece off. This way I didn't have to try and slide the two interlocking pieces apart.

When you go to put the new piece on before you interlock them make sure they are put on right. Specifically the latch is pointing the right way to seal the detergent door. Otherwise it can be a pain to separate the interlocking pieces again. (which is why I cut it off the old one).

Then you're done. Just put it all back together.

Disconnect power supply to dishwasher. Open door and remove screws on inner door cover. Carefully remove inner cover while watching how inner parts are arranged. Found return spring on detergent cup linkage had rusted and broken causing detergent cup not to open. Installed new spring and re assembled inner cover. Rotated timer dial one fu ... Read more ll revolution to check operation of detergent cup. Worked like a charm. Re connect power supply to dishwasher and your good to go.

removed old parts and re-installed new parts. The spring is a little hard to get to the right point without a jewelers screwdriver, after that everything worked fine.

After doing some research in a repair book I decided to take a stab with a water inlet valve. With expedited shipping I ordered the part and within three days it was delivered. I installed it and the dishwasher seemed like it was trying to fill but still would not. After much cocnsternation I turned the water supply valve to the dishwash ... Read more er a partial turn to close and I felt the water rush through the valve and the dishwasher then filled. Apparently the shut off valve must have been clogged plus it now leaked. I then replaced the shutoff valve and the copper pipe to the water inlet valve with flexible 3/8" tubing and the dishwasher thus far is running fine without leaks.

I turned off the circuit. I removed the interior side of the door and then the plastic covering over the electrical wires and switches (I counterbalanced the door with a couple of half gallon juice containers). I removed the wires attached to the switch on the door handle and the door handle itself. The handle and switch parts disassem ... Read more bled and I replaced the switches (part of kit). I cut off the singed wire and the other three beyond the damaged portion and stripped the wires and connected the extensions (part of kit). I attached the new wires to the switches and closed up the interior door. Lastly, I turned the circuit breaker back on. All was well!

After completely pulling out the dishwasher, I removed the rubber housing that connected to the housing assembly. I unscrewed the retaining ring which holds the impeller in place and then pulled the impeller off the shaft (which took quite a bit of force). I removed the seal seat ring and using the impeller and seal kit I replaced all t ... Read more he internal parts to the impeller system. (note: the impeller and seal kit acutally contained the seal-head and seal seat ring so I was able to return those two parts.) I put all of the disassembled parts back together.

I removed all the ( what my Husband called star screws ) star screws and removed the housing panel ( holds dish detergent cup and silverware basket ) I discovered everything accross the bottom was all gucked up with detergent soap accumulation. I took the part to the kitchen sink and used the sprayer hose on the part with hot water and i ... Read more t cleaned up beautifully, and the detergent latch then worked ( the spring that operates the latch was all gucked up with detergent accumulation ).
I am the wife and did all of this myself and it only took around 5-10 min. My Husband had to help me figure out the type of screws because they turned out to not be phillip screws, but as Hubby called them.."star screws".
Soooo, I did not need to use the Latch Kit I purchased, so will store it in my parts supply! :)
Happy repairs to you..
Judy Estes Park, CO

Turned of water and unplugged the dishwasher.
Disconnected the incoming water line.
Drained on to the floor (have paper towels ready)
Disconnected the electrical feed wire.
Disconnected the rubber hose.
Unscrewed screw holding the fixture to the frame.
Took off the brass elbow from the old part.
Put pipe ... Read more dope around it and screwed into new part (carefully, so as to not crack plastic again).
Attached part back to frame.
Attached water lines.
Turned on water, plugged it in and ran dishwasher looking for leaks. No problem.

replaced the two water defiector's, I had changed the door seal and should have changed the defiectors at the same time. Save yourself some time and ordor both parts. This is a easy fix, anyone can do.

I snapped on the new part onto the track. It was that easy! :) Thank goodness the part was available from Part Select!
T. Edwards

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

I unscrewed the old water inlet valve from the frame of the dishwasher so that I could manuever my hand around to the backside where the rubber hose was connected. That was the easy part. I then had trouble holding the old valve while trying to unscrew the hot water copper tubing so I screwed it back on the frame. My dishwasher is clo ... Read more se to 18 years old and I think that was part of the problem. After soaking in WD40, I finally got the valve out. Then I had to remove the "L" shaped connector to put on the new valve. Everything went back together a lot faster and it's like I have a new dishwasher again. By the way, I am a 53 year old female so that may be why it took me so long.

Had to pull the dishwashwer out to replace the latch. Did this by unscrewing the 2 screws that hold the Dishwashwer to the under side of the counter. Dishwasher then pulled out easily. Then unscrewed to screws on the latch. The screws were accessed by pulling out the modling/strip around the dishwasher door. Also easy to replace the ... Read more screws. But sliding it back in was a little harder. Had to shorten the front legs on the dishwashwer to get the back of the dishwasher to go back in. Then screw the front legs back out. Finally re-inserted the screws under the counter that attached the top of the Dishwasher to the counter top.

I removed the inner nut holding the spray arm onto the pump. Turned the washer on it's back and removed the wire clip holding rear of the pump motor. Completely removed the pump housingand motor from the washer. Removed three(3) long screws holding the motor to the pump housing. Removed the dish from the housing and removed the old impel ... Read more ler and seals .
Cleaned the pump housing of calcium with lime-a-way. Reinstalled all new parts in reverse order as they order taken off. Cleaned inside of dishwasher with lime-a-away and general purpose cleaner. Reinstall pump housing and motor on washer in reverse order as they were taking off.
Reinstalled washer into cabinet and connected all hoses, drain lines and electrical wired. Turned washer on and watched it run throught a complete cycle. Worked just fine and no leaks. Parts were great.

Sincerely,
James