RUD1000DB3 Roper Dishwasher - Instructions

The repair was very simple. Simply pull the dishwasher out far enough to access the springs, remove the old with pliers and install the new springs in the same spot as the old ones.

I just followed the video, and it now works perfectly! Thanks SOOO much! great site, great info.

Shut off water supplyand removed front cover below door. Remove flexable water line (wrench set), valve and bracket (nutdriver), and input hose (pliers). Installed flexable line on valve, replaced input hose on valve, then installed valve and bracket. Found screen on input to valve almost completely blocked with buildup of materail. Repla ... Read more ced front cover. result, bright, clean dished.

I watched the video, read all the post, they all said change the heater. So I did. Only there is a little fuse at the back of the unit that also goes bad and that was my issue. Have it ordered and will be going soon. That said, Part Select made finding and getting my parts a breeze!

Made sure the power and water were not connected to the dishwasher. Removed the bottom panel. Unhooked the old part. Put some plumber's tape around the threads, hooked it all back up. Runs just as good.

Followed vidio instructionson web site. Quick easy fix

Performed repair as to Video shown in receipt after purchase of spring plus we used a friend who has same dishwasher and has performed the same repair recently, video was easier to follow though. All you do is push off lid with a screwdriver and pop off as per instructions on video then unlatch spring from ledge and pull off post, then ju ... Read more st reinsert new spring in reverse order or follow video instructions either way is easy and takes about 15-20 minutes to install

The top of the latch was broken on I had to push the plunger back through the mounting to get it out. ai had to pull the whole assembly apart to get the locking nut out. i remove the latch assy and took about 10 minutes to figure out how to put it back together. Changing it with the help of the video wasn't hard but confusing at times. T ... Read more hanks for the video.

Bought a house and with it can an old whirlpool dishwasher in where the soap dispenser lid would latch, as the latch itself was gone. Ordered the latch from part select and used the installation video to switch the latch out. Only problem I came across was that the torx screws at top of he door were free spinning. Ended up using a flat he ... Read more ad for leverage to finally get the screws out. Everything works perfectly for once.

Trial and error. The spring was difficult to install, the pin and door were easy.

i took the inside door off and took the 2 switches out and replaced them; not too difficult.

The video was of great help. One area that gave me grief was placing the small part with points under the plastic mechanism in the door. I tried to push the points into the open slot. After watching the movie a few more times I was trying to put the part in backwards. A little more explanation at this point in the video would have been a ... Read more tremendous help. Otherwise, thank you for the video.

I replaced the seal, still leaked. Once I noticed that it was only leaking from the left side, we did a Google search to find that the screen in the upper left of the door could be the issue, causing back pressure. Once the screen was cleaned, no more leaks.

I read everyone else's fixes, which were very helpful but my solution of removing the plastic from the motor shaft was a lot easier than others. I simply used side cutters and made two cuts into that plastic piece and it Fell of. much easier than the person using several Dremmel blades to cut it off.. That was the most difficult phase unt ... Read more il I grabbed my ole phone company side cuts and just cut it off in 15 seconds. Thanks for all the other tips. I love dealing with Parts Select, Fast and efficient. Jim W

Unplug dishwasher from electrical, water supply and drain hose. Pull dishwasher out from under cabinet. Unscrew water whirler from inside washer, then remove motor. Remove black boot from motor. Unscrew keeper from impellor housing. And you are there! Pull impellor off motor shaft. Replace seal first, then replace impellor. So easy this g ... Read more irl did it. But, this girl also does small engine repair!