- Home
- RTWD187SL-5
- Instructions
RTWD187SL-5 General Electric Refrigerator - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
My light in the refrigerator was going on and off.
1 person
found this instruction helpful.
-
Nan from PURCELLVILLE, VA
- Very Easy
- Less than 15 mins
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this helpful?
Thank you for voting!
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
1 person
found this instruction helpful.
-
Robert from SAN DIEGO, CA
- Really Easy
- Less than 15 mins
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this helpful?
Thank you for voting!
bulb out
1 person
found this instruction helpful.
-
Kenneth from Rowe, VA
- Really Easy
- Less than 15 mins
I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.
Was this helpful?
Thank you for voting!
Fridge light dead even with new bulb
1 person
found this instruction helpful.
-
marj from NEWBURY PARK, CA
- Really Easy
- 15 - 30 mins
-
Screw drivers
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this helpful?
Thank you for voting!
Short in the light socket.
1 of 2 people
found this instruction helpful.
-
ED from ENON, OH
- Very Easy
- Less than 15 mins
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this helpful?
Thank you for voting!
socket had melted
1 of 3 people
found this instruction helpful.
-
Chris from Charlotte, NC
- Really Easy
- Less than 15 mins
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this helpful?
Thank you for voting!
Light socket missing in refrigerator
1 of 4 people
found this instruction helpful.
-
Wayne from Issaquah, WA
- Really Easy
- Less than 15 mins
Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.
Was this helpful?
Thank you for voting!
all power to refrigerator quit
-
Paul from Irving, TX
- Really Easy
- Less than 15 mins
-
Screw drivers
layed fridge face first on a chair removed cover with flat head screwdriver unplugged part replaced with new part replaced cover returned to upright and plugged in
Was this helpful?
Thank you for voting!
light would not stay on
-
Kenneth from Leavenworth, KS
- Easy
- Less than 15 mins
First I flipped breaker to off position for refigerator, Pulled down on socket and broke it free. Then took needle nose piars to pull wire and plug out from hole, so I could conect to new light socket then snaped it in place . Hardest part was getting wire and plug out of hole.
Was this helpful?
Thank you for voting!
needed new light socket
-
Charles from Williamsburg, VA
- Really Easy
- Less than 15 mins
Pulled out old socket.pushed in new one.
Was this helpful?
Thank you for voting!
The bottom part of fidge was warm with water droplets on the its ceiling.
-
Charles R from Renton, WA
- Easy
- 15 - 30 mins
-
Nutdriver, Screw drivers
Removed Ice shelf,
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart b ... Read more rackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Remove rectangle cover by removing the two screws and lifting straight up.
Pulled fan off slowly.
Removed two hex screws holding motor bracket.
Remove cover.
Remove two hex screws holding remaining bracket from fridge.
Pull wire off motor noting where they were plugged in.
Pull apart b ... Read more rackets holding motor and remove motor noting how the motor and brackets fit together.
Reverse to install.
Read less
Was this helpful?
Thank you for voting!