RSS399 Caloric Range - Instructions

The first one came damaged and customer service credited the first one and got another on the way the same day. They were awesome to deal with. I removed the oven racks, the burner cover, the storage drawr, and the door. That took about 5 minutes. I removed 3 screws that held the ignitor in place. I removed the 2 wire nuts from the wires ... Read more in the drawr space. I slid the ingitor cover off the old ignitor and onto the new one. Slid the new ignitor into place and fed the wires below and put on the 2 wire nuts, then installed the 3 screws and tested the operation. I put the oven back together and put the tools away. Total time about 20 minutes.

shut off gas at tank, pulled stove out from counter area to gain acess to back, removed oven door removed removed screws holding igniter unit in place, i then removed the stove rear panel to get at the wiring for ignitor,remoded old part returned to front and installed new part, checked voltage then re-connected new wires, turded gas back ... Read more on and tested oven, oven came on less than a minute, put rear panel on stove put door back on and put stove back into counter area, stove works like new.

Removed burner with attached igniter assembly by raising forward legs from slots and pulling unit from rear support. Note: this is contrary to instruction #1 on installation instructions. Then followed the remaining instuctions 2 - 7 as written. Everything worked as planned.

Very simple process of just ensuring you have the correct size racks and remove the old racks and replace them with the new ones.
Having ordered a lot of things on the internet, I am very pleased with using Part select and would "highly" recommend them to all!!

removed the shield and removed the old tube. Replaced with the new tube and replaced the shield. The only place I could locate this tube was through the internet. This Co. had as good a price including shipping that I found.

ordered new broiler pan

First turned off power to oven, Took burner out by lifting up and pulling out, then pulled out wires attached to the oven and igniter, removed two wire nuts and disconnected the wires then removed burner assembly from oven. With screwdriver and nut driver removed old igniter from housing and put new one in place, tightened up screws carr ... Read more ied back to oven reattached wires with wirenuts and feed wires back into oven, then put burner back carefully silding igniter into hole in back of oven. Turned power back on to oven and worked nice. Took all of 15 mins to complete.

I just replaced the racks with beautiful, new, shiny racks. My wife was very pleased

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

The repair was quite easy. Remove the two screws and put in the new part. The only problem I had was the hinge sent was the wrong side (but it still worked) and the new hinge had no threads for the screws. I had to tap the holes so that the screws could be used.

After I received the new hinge in the mail, my 13 year old son volunteered, for a fee of five dollars, to put the new hinge on the oven door. Seeing "easy to install" on the outer wrapper of the new part, I thought I was being generous. However, my son soon let me know that the screws given with the new hinge did not fit into the predri ... Read more lled holes of the oven. He tried and tried for over an hour to get those screws to fit. I decided to go to the home improvement store to buy bigger screws. I took the hinge with me and had the store employee assess the type of screws I would need. He then informed me that the screws were fine, but I needed the holes in the hinge to be drilled bigger. I bribed him by offering to buy him a drink if he'd do it for me as long as he was single. He laughed and drilled away. (Sometimes, single women, like me, get desperate!) He handed me the hinge with larger holes and I noticed the wedding ring. Oops...no drink for him!! But I did give him a great big thank you. Happily, I brought the fixed piece home and handed it to my son to continue with the repair. He tried again and this time announced the holes were drilled too big!! If there was a bridge nearby I seriously would have jumped! The next day I drove to my Dad's house...a true jack of all trades...and with his drill and two new screws, he said this should do it. For the third time, I handed the hinge to my son and VOILA!! It actually worked! Thanks Dad!! So much for "easy to install". Seriously, the incorrect screws were sent with this hinge! Anyway, I happily celebrated that night with a drink in my hand...minus the home improvement employee!

Ordered a left & right hinge. Paid considerably more for the left hinge but both hinges were identical when received.
Bolt holes in both hinges were not tapped for the bolts which were sent with the hinges. This required a trip to the hardstore to get a tap set. After the bolt holds were tapped there was no problem removing the old ... Read more hinges and installing the new ones.

Slide stove out unplug remove cover on back bottom left 3 screws remove wires from old module and plug into new module could not remove old module I glued new to old replaced cover pluged back in slide stove back in and the burners lit

I found the ignitor was wired in series with the gas valve and wasn't letting enough voltage through to the gas valve to open it. I just unscrewed the ignitor and pulled it out.

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.