RS464J2 General Electric Range - Instructions

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the meta ... Read more l correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Gasket sent did not match the profile of the original. Only after trimming off two long edges of the gasket did it come close to matching the original. I would not recommend using this replacement gasket for this oven model. 1-Remove door. 2-Loosen the 2 oven box attachment nuts on the back of the oven. (loosen only, about 3/8") 3-slide ... Read more the oven box toward the front of the oven. 4-remove old gasket, and insert new. 5-Retighten 2 oven box attachment nuts. 6-Reinstall door. Took especially long because of incorrect gasket. Deep well socket required to loosen oven box attachment nuts. Recommend two people to do, one in back, for attachment nut and one in front to keep gasket in place while tightning nuts.

Read and follow the instructions. Be careful when stripping old wires to attach to new element. Fit the element to ceramic casing prior to attaching wires. If new element does not seem level after replacement heat a large pot of water. The element will expand and the weight of the pan of water will settle the element. "Physics 101"

Took off the door, took out the two screws in the back of the element. Then pulled the element forward, then removed the two wires. Then put it all back together with the new element.

Turned off power to the oven at the circuit breaker. Pulled the old heating element from the back lower wall of the oven. Noted the position of the wires (right terminal attached to the red wire, left to the black wire). Removed small bolts holding the element to the wires using pliers. Attached the new element using screw driver. New ele ... Read more ment came with screws, not bolts. Pushed the element back into place and restored power. Tested to make sure everything worked. Everything works and I ran an oven cleaning cycle. Noticed that indicator light above the temperature selctor is always on now even when oven is in the OFF position. Not sure if that's related to the change or to the oven cleaning cycle I ran. In any case, oven seems to work normally.

It was so simple, I turned off the breker to the oven, unscrewed two screws holding in the element, pulled out until the wire connetion was exposed. I unscrewed those two screws, then placed the replacement part, put the two screws on, pushed back the wiring and insulation.Final step was screwing two screws to hold the unit to the oven ba ... Read more ck. So simple! The part was ordered regular mail and still was here in 2 days. Will recommend to friends for sure!

Unscrewed the element from the oven,disconnected the two screws for the electrical and reverse the procedure to install new element. Took all of about 10 minutes.

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped ... Read more the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

I couldn't find the oven model number so I just looked at the shapes from partselect.com. This would have been fine except I didn't know my Kenmore model had 4" leads so the one I ordered were only 2". I had to return the first element but the process to do this was FAST and EASY. With help I found the model number and had the correct par ... Read more t shipped. It took less than 5 minutes to install. It took longer to mop and clean behind the oven that hadn't seen the light of day in 10 years.

First I read the already posted repair stories to give me confidence I could perform the repair.
Followed their steps -
Removed the two screws holding the plate to the oven.
Pulled out the element.
Removed the two screws holding the wires to the element.
Installed the new element by attaching the two screws (which ... Read more were supplied) to the element.
Reinstalled the plate to the oven.
Tested it and it worked perfectly saving a costly service call.

It was so easy. Just removed the cover and then unscrewed the wires (keep track of which wires go to which side). Do teh reverse to reinstall

Repair was as easy as one, two three. Turned off the power and removed the two screws holding the element in place. Then pulled the element out approx. 3 inches and removed the two screws connecting the wires to the element.

From there I reversed the process and the repair was complete in less then 5 minutes, and I am not a el ... Read more ectrician.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.

replaced burner ( attached wth 2 screws )

Removed two screws and take Element out and put new one in.It is very easy to do.