RS46404 General Electric Range - Instructions

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Removed the old piece and connected the wires to the new piece. I'm a woman and this took me less that 15 minutes to complete. Easy as pie. On top of that, I received my order within 3 days! Very ... Read more impressive, PartSelect. Thanks.

The first thing I did wrong was order the wrong part. Then later I did find the Model number on the side of the bottom drawer. I reordered the right part and turned off the electrical breaker. Removed the old element. I then installed the element in the oven with 2 screw nuts and pulled out the stove, took off the back panel and slipped ... Read more the wire nuts onto the element. Very simple. I am really thankful there is a place to order the part and it came the next day after I ordered it. WHOW!

First I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I removed the old element from the oven and replaced it with the new element. Then I connected the two wires to the new element and pushed the element into place. Then I replaced the two scre ... Read more ws that held the element in place. I then tested the oven and it worked wonderfully.

This was so easy to do. First I took the two screws out of the holding plate. Then the element comes out and I took the two screws attaching the wires to each end of the element out. To replace it just reverse the above and turn it on let it heat for about 10 mins to burn off any residue and you are ready to start baking again. A ... Read more lthough not really necessary it is reccommended to unplug or turn of the breaker before you start working on the problem.

First, we turned off power to the range. We removed the screws holding the element to the back wall of the oven and pulled out the element a few inches. We disconnected the 2 wires from the old element, and attached the new element with the 2 provided screws. We pushed the element back into the wall and secured it with the screws. Tur ... Read more ned the power back on, turned the stove back on and, voila, the frozen pizza was well on its way to becoming dinner!

4 screws 4 off then 4 on done

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...I copy and pasted this from their example - it really is that easy - this is a simple repair.

replaced burner ( attached wth 2 screws )

Removed two screws and take Element out and put new one in.It is very easy to do.

A friend had stopped by and insisted on replacing the heating element on my 32 year old range. It took him all of 45 minutes to replace it, and now it works like a charm.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Followed instruction that came in the new parts. Each element took about 10 minutes to remove, inspect the wires, clean the connections and reconnect the new elements. The element covers that came with the kit were easy to install, and everything fit just fine. Most important thing is to turn of the electrical power to the unit BEFORE ... Read more you start.

Hi, First unplug appliance ,remove the oven door by pulling it up from the hinges, giving room to work deep inside , remove the two screws that hold the element in place. then pull the element out carefully not to stress the wires and replace the element . Note after all is done test with an oven thermometor :)

Unplug range from its 220V source. Make sure range is not hot from recent usage. You’ll need a #2 Philips driver, preferably one with 14-18 inch length. The old screws will likely be very stubborn about coming loose. Two of them hold bottom element in. Remove the back panel so access to the two connectors on the bottom element are easily ... Read more removable. Be very careful not to the let the wire connectors from the heating element drop down into the insulation. For the top element, there are four screws holding it in place, I found it was easier to access these two screws leaning the range backward at a slight angle. Take special care again not to let the wires drop down into the insulation. The connectors to the old element will likely need some extra effort to remove. The reconnection to the new elements should be ok. Make sure all screws go back in that were removed. The new elements will be amazing, and baking and broiling will be like new again.

I initially only purchased the heating element since this usually the cause of the broil element not functioning well. It took a little longer to receive because I had to order it over the Holidays. Once it arrived it was very easy to replace. It worked very well after installation but the broil element still did not function. I then pu ... Read more rchased the broil element and received it within approximately 4 days. It took just a little more time to replace because there was a brace that was attached to the upper oven that helped to hold it in place. Once the wires were attached with the screws it worked very quickly. It's nice to have my oven back in use again!