RLD313 Caloric Range - Instructions

I removed the 2 screws that held the housing on at the back of the stove. Then I removed the 2 screws that held the module to the back of the stove. Since I am not an experienced electrical person (I am a female nurse in the operating room), I unplugged 1 wire at a time from the old module and plugged it into the new module. I repeated th ... Read more is step with each wire to make sure I didn't put the wrong wire on a wrong spot until I had all the wires to the new module. Then reattached the screws, plugged in the oven and presto, it works just fine! Was amazed at how easy it was. A 50 dollar part instead of a new 1500 dollar stove. How easy is that?

Had to remove the 4 range knobs, and the oven knob and then the facie. Two screws under the end caps and two on each side from the back on each end. Design defect: one of these screws which attaches through the frame to the facie also attaches the support which holds up the range top. Take that one off last. Remove the two wires that atta ... Read more ch to the oven light switch. After detaching the power supply to the defective ignition unit, it just pulls right off. Push the new switch on over the knob shaft and reassemble.

The knobs were a perfect replacement and I just slid them onto the posts on which the old ones were on. Although my range is a Glenwood I think that the parts are now made my Whirlpool (not exactly sure) but they are a perfect match. My order came so quickly and I am thrilled with the transaction. I didn't think I would ever find the r ... Read more eplacement knobs and thought I might have to get a new range as you could not read the oven temperatures at all on the old knobs.

I didn't. Don't know how to get to light bulb to change it for this specific model

Removed the burner plates. Lifted up the range top. Removed the knobs. Unbolted the 2 rounded nuts at top of face plate. Removed the 4 screws that hold the face plate in place from behind. Un plugged the old switch and plugged in the new one and bam! The burner worked. Thanks, Super fast shipping! The part was here in less than 36 hours. ... Read more John, N.J.

I used the experience of another user posted on your web site. I removed all the gas control knobs and then I followed his instructions about removing the four phillps head screws that held the front plate in place. Once I had it loose and flipped the plate out, it was simple to disconnect the old ignitor switch and install the new one. ... Read more Simply reversing the process put the range back in proper order. Took a little over 15 minutes to accomplish.

1. ordered two new switches
2. installed switches
3. all ignitors work

Really appreciated the pictures of the parts--made selection very easy.

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

shortened gasket for this oven. moved hook approx. 1 inch. used high temp adhesive. simple fix.

Took the old knobs off and put the new ones on...voila!!
They fit perfect and even had the same part number stamped inside. Perfect fit and just like new!
Wasn't much of a repair per se but wanted to give a good review. The old knobs were over 30 years old so I was worried I wouldn't be able to find an exact replacement but Pa ... Read more rtSelect had the exact match.

I pulled off the old knobs and then placed the new knob. No tools needed!

I have a gas oven range and 2 of the knobs were stripped, making it difficult to control the heat. My appliance is at least 20 years old. I thought I'd have to replace the whole thing. I found your website, did a search, and found exactly what I needed. The knobs fit perfectly. Although not an exact match to the originals, they work, and ... Read more that's all I care about. Easy and inexpensive fix.

The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new ligh ... Read more t bulb in was not the problem.

1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.