RK960G001 Hotpoint Range - Instructions

PS240270
Ceramic Fuse - 15 Amp
Easy installation , remove microwave cover housing ,locate fuse by door catch & replace..
Received quickly..
Replaced fuse , removed microwave cover housing , located fuse adjacent door catch removed & installed new fuse...

First, and most importantly, flipped the circuit breaker and turned off the power to the oven. Next, Unscrewed the old element and disconnected the wiring. Then, removed the old element and replaced it with the new one.
Reconnected the wiring to the new bake element and screwed it back onto the oven.

Voila! Turned the ove ... Read more n on and watched the new element heat to a bright red. We had an oven once again, and saved ourselves more than $100. Yay!

The Baking elements takes 10-15 minute each but the Broil Element is a bit tricky as the screws holding the element is difficult to get to. I also used duct tape to temporarily hold the element to stay in place.

First I removed the two screws in the back. then I removed the two screws attached to the brace at the top. pulled the old element out. Removed the screws that attatced the wires to the element. Attached the wires to the new element. Pushed the wires back in. Pushed the element in and attached the screws. Reattached the support. Turned on ... Read more the broiler. The element smoked for a few seconds before getting red hot. It is working fine.

Pull the stove out from the wall and unplug. Had to remove back of stove, the aluminum sheilding and the duct work to get at wires use nut driver. Then used nut driver to remove nuts from broiler unit inside stove. Take the front overn dover off first. The new part did not match up with the wires so I used a needle nose to spread the wi ... Read more re clips just a tad so they would fit over the tabs of the broiler unit. Do all of this behind the stove as you do not have eough wire to do this effectively from the oven side. After I had the tabs fitted to the broiler unit. I removed them and fed wires back through the stove. I then went back to the front of the stove and put the broiler back in and put support bar back in to ceiling of stove and the two nuts back on to affix broiler to back of oven. Put the aluminum baccking and duct work back onto the back of the stove and plugged it back in. Pretty easy job.

Ordered Bake Element - 240V from Partselect , when part received removed broken element with a screwdriver., replaced with new Bake Element with a screwdriver. Very easy to do.

Turned off power at panellboard. Disconnected mounting hardware from inside oven chamber. Pulled failed heating element with wires attached into the oven chamber. Disconnected wiring and reconnected them to the new heating element. Tightened screws while holding connectors with pliers. Applied electrical tape to connections. Pushed wires ... Read more back into opening and secured heating element back into place. Restored power nad verifed proper operation. The other heater purchased will be used when the bake element finally fails,

(1) Turned off power source.
(2) Removed rust on screw heads before attempting to loosening them up.
(3) Pulled the element out to expose the connections.
(4) Disconnected with phillips screw driver, taped off wires to prevent mixed-up during re-installation.
(5) Re-installed new element using new screws provided.

Removed the racks, removed two screws holding the element to the back of the oven, removed two screws holding wires to the element, installed by the reverse. BUT in my case the new element still didn't heat. The part was perfect so when the old element melted and shorted, it must have damaged the controlling switch (220V requires dual p ... Read more ole switch--apparently one side is now bad). Since the oven is over 30 yrs old, I'm returning the element and will buy a new oven.

I turned off the breaker to the oven. Removed the old element and replaced. Turned on the oven breaker and turned the over to 350 and it was working great. I was very proud of myself as a 68 year old widow.

USE A MAGNETIZED SCREW DRIVER. BE CAREFUL THE OVEN ELECTRIC WIRES DO NOT FALL BACK INSIDE OF THE OVEN. HAVE LONG NOSE PLIERS HANDY. MAKE SURE YOU TILT THE ELEMENT SO THAT THE ELEMENT TERMINALS ALIGN PROPERLY WITH THE THE SCREWS AND ELECTRIC WIRES. THAT'S IMPORTANT ELSE YOU CANNOT GET THE SCREWS STARTED TO ATTACH THE ELEMENT.

Turned off the power to the oven. Removed the racks. Removed two screws holding the unit to the back of the oven. Removed two screws holding the wires to the terminals. Removed the old unit. Reversed the process. Piece of cake. The only "difficulty" was that the old wire-to-terminal screws required a nut driver (as did the unit-mounting s ... Read more crews) while the new wire-mounting screws required a #2 Phillips screw driver. Took me a couple of minutes to get one of those from the garage.

First I cut the power then I pulled the mounting screws, pulled hte elements out enough to get the screws out and then did it in reverse. Piece of cake.

Two 1/4 inch screws and then two Phillips head screws that was it

Removed the nuts securing the element to the back of the oven, pulled out the wiring and unscrewed the wires. Went on line and found the part, ordered it, received really quickly and put the part back in the oven. Works great. Oh, I also turned off the power.