RH962G3M1 Hotpoint Range - Instructions

1) Turn off power at circuit breaker panel
2) Slide out Range from wall
3) Unplug Range
4) Remove back panel and unplug electrical connections to socket
5) From front of oven, remove glass cover over old oven light bulb and remove flange that holds socket and bulb
6) Remove old socket from mounting flange and disc ... Read more ard.
7) Place new socket into mounting flange
8) Screw mounting flange and new socket into the oven from front. Reattach electrical connections from back.
9) Screw in new light bulb from front
10) Replace existing glass cover over new light bulb and snap wire holder in place
11) Replace back panel
11) Plug in range
12) Slide range back to original position
13) Turn on power
Works like a charm! Thanks for having the parts after 30 years!

Disconnect power. . . Remove control panel, pull wire connectors,[note location] remove old switch, install new, install wires, snip stem to length, set knob . . . Turn on power - works. [Note this is a live part even when not connected]

1. Bought replacement part said to replace old switch.
2. Pulled old switch out.
3. Replacement part did not match. Would have to take entire switch panel apart to change to this part.
4. Multiple-part instructions very poor. For my switch unreadable.
5. Old part was "push to turn". New part was not.
6. Knob did ... Read more not fit new switch. Old shaft was "D" shaped. New is square.
7. Gave up. Need to call repair shop.
8. Hope this helps.

shut off electricity to the range, removed the screws holding the element in place, pulled the element out as far as it would go, removed the screws holding the wires in place, tossed the old element, attached the wires to the new element, pushed the element back into place and reattached the screws holding the element in place. Turned th ... Read more e electricity back on and the oven heated right up.

Also, the part arrived the day after I ordered it. Great Price & Great Service.

1. Make sure electricity is off!
2. Remove 2 screws at rear of oven where the bake element is attached.
3. Pull out far enough to remove the 2 screws where the wires attach.
4. Lift out the old element and set the new one in.
5. Reattach the wires.
6. Reattach the element to the rear of the stove.
7. Turn ele ... Read more ctricity back on.

Easiest thing I've done. Shut off breaker. Unplug range. Pull out from wall (because this is a good time to remove the back, clean under and around the unit, check out the insulation and electrical contacts....or skip it, whatever). Open oven. Remove door (while ajar, pull up). Remove racks. Unscrew mounting plate from back interior wall. ... Read more Set screws aside. Gently pull element forward until the leads and wires come through the insulation. Remove any strands of insulation that stuck to the leads and connectors. Unscrew leads. Keep left wire to the left and right wire to the right. DO NOT CROSS. Set screws aside. Discard old element. (This is a good time to clean your oven, if you haven't in a while.) If you cleaned oven, wait until dry. Position new element, feet down, in bottom of oven. Position left wire on left connector. Screw tightly BUT DO NOT BEND LEAD. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Position right wire on right connector. Screw tightly BUT DO NOT BEND. IF YOU BEND IT, THEN DO NOT BEND IT BACK. CALL A PROFESSIONAL. Do not leave screws loose. Connection must be tight. Fire hazard, otherwise. If you bent nothing, then gently push element back through insulation until mounting plate is flush. Screw into position. Replace racks. Replace door. If you decide to check insulation and other leads, now is the time. I checked mine and it's a good thing I did.... Unscrew back plate of oven, keeping screws in order. Remove plate. Check that your new element and insulation aren't bunched up or otherwise in a hazardous state. You may notice burned or greasy insulation. You may see burned leads on light receptacle and broil element. If you do, then replace them, too. When finished with everything, replace back plate. Put range back into position, ensuring level and plumb. Plug in. Turn on breaker. Pat yourself on the back. You just saved $100-$250, depending on where you live.

Replace part an wires

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the ... Read more switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

Simple repair that was complicated by not being able to remove the oven door, leaving a long reach to the element connections in the back of the oven. Other than the accessibility issue, the repair is easy. Remove two scews, pull the element out about 3 inches to access and unscrew the screws holding the wires to the element. Then reve ... Read more rse the process with the new element. But, because of the long reach, there were alot of dropped screws and cussing.

turn off electricity to stove and simply remove the screws from the heating element and put new element back in place .put screws in and turn power back on and test.

Partselect made this job a breeze. Due to the user friendly process to order and receive the part. I repaired the stove after turning off the breaker in the main box. There were two screws that held the baking unit in place, removed them and then replaced with new unit.

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.

Got new part! Unplug range!!!
Remove oven door by opening and lifting up at the same time, set aside.
Remove two screws with a nutdriver or screwdriver.
Pull on element far enough to unhook wires and throw away old element and install the wires on the new element and reinstall!!