RH758*V8 Hotpoint Range - Instructions

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

No. 1 thing I did is I unplugged power supply to oven, second- unscrewed two screws that was holding cover plate and removed cover plate with a set of pliers, pulled element out and unscrewed two screw with power wires and installed new element, tightened screws and re-installed cover plate, tested oven turning on oven and in a few second ... Read more s element got hot, job done!

First I turned off the breaker to the oven,
then I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I placed the new element in the oven, reconnected the wiring and replaced the two screws in the mounting bracket. I reset the breaker and turned the ove ... Read more n on to about 450 degrees for 30 minutes to burn off the new smell of the element. This job was very easy and I saved about $100 from paying a service to do it.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to ... Read more come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

I removed the burner, then the chrome dish. The nuts for the wires were rusted to the terminals, so I had to break the module apart and grind the nuts off.After that the new module went fine.

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

Actually you are right, I removed the two screw pulled the element out , disconnected the two wires holding the old element and put the new one on. I spent more time finding out whether or not it would be safe to work on it, being on my own for the first time and always had someone do it for me. I was told as long as the oven was not ... Read more on it was safe and so I went to work. I was also very impressed at the short time it took to get the part. Three days!!!!!!!!!!!!!!!!!!

Two screws to remove the element and two screws for the wire connectors and it was done.

First I turned off the power to the stove,removed oven racks,removed the two screws that held the element in place,pulled unit out a couple inches ,removed the two screws that held the wires in place ,removed element.
Placed new unit where old one went and placed wires in proper order and put together and placed back . turned power ... Read more back on and WALAA......nothing......apparently that wasnt the problem....Husband baught me a new stove,after 35 years why not.

.....then tested for voltage, had it. Ordered the element through partselect.com and it came in the mail THE NEXT DAY! No kidding! Installed it and the wife is back to her good cooking. All is well, thanks partselect.com. John R., Pompano Beach, Florida

removed the old, replace the new. The delivery of my new part was exceptional, received the very next day after ordering.

1)Unscrewed the mounting nuts, 2) pulled the heating element out a couple of inches, 3) unscrewed the screws holding the wires in place, 4) removed and tossed the old heating element, 5) placed the new heating element in place, 6) re-screwed the wires to to the element, 7) pushed the heating element back into the wall of the oven, 8) rese ... Read more t the mounting nuts, 9) cleaned up the work area, 10) cranked up the oven and made a pizza. I'm not particularly skilled when it comes to things of this nature, but it was ridiculously easy...

All other reviews decribed the repare process that I used with no problems. The only reason I took about twenty minutes instead of around 15 minutes was it took me a few minutes to get the correct socket to remove the two small lag screws of the old bake element to free it from the oven wall. I did not have to remove the oven door as it w ... Read more as not a problem in reaching the back of the oven. My range is 25 years old.

The only hard part of the job is removing the old, corroded terminal block. Be careful not to break the electrical wire. Other than that, just sand the contacts and reassemble. This is the second one I have replace on my 4 burner stove. 2 more to go.