RH657*V4 General Electric Range - Instructions

Unplugged range. Removed old element from back of oven which was held in by two screws. Unscrewed the wires that were attached to old element and screwed them into the new one.

removed the two screws, unsnapped the burnedout element and snapped new element in place, replaced two screws.

Could not believe how fast the part shipped. 2 days and it was here. All it took was using a nut driver to remove 4 screws and then put the new one in.

With great ease. Only thing I would have appreciated was knowing the size ofvthevrequired socket wrench. Otherwise it was easy and fun as the instructions were crystal clear.

My 17 year old son and I (his mom) replaced the oven element in less than 15 minutes!!! It was so easy. We first unplugged the stove since I didn't want to go and shut off the circuit breaker in the dark!! We then removed the two screws that hold the element in place and started to pulled out the element. It was actually corroding in m ... Read more y hands as I pulled it out. We disconnected the wires and then put in the new element by reconnecting the wires, pushing the connections back in and replacing the two screws that hold the element in. The oven heated right up!!! What a savings to do it yourself and not have a repairman charge us extra to do a 10 minute job!! Thank you Part Select for your fast service. I will definitely look here before I shop anywhere else. Thanks,

Four screws and two wires.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Then I replaced it with the new element that took only two days to arrive and that was without paying extra express shipping fees. It couldn't have been easier. I didn't even wait for my husband to ... Read more come home and install it. I had an oven-baked meal ready when he got home. I was very satisfied.

Your "virtual repairman" was fantastic. I would have purchased the wrong part without trhe diagnostic service. It said that 53% of the time the infinite switch was the problem. In my case it was 100%. Why I put up with this problem for 6 years I will never know.

Repair job was easy but longer than the 15 minutes that it said ... Read more it would take.

First of all I did this repair because the wire to the burner shorted out. I did the wire portion first - only then did I know I needed the switch kit. (The burner was operating while my old swithch was OFF). The first (wire replacement) repair took about 10 minutes - I followed the guidance on this web-site. The second repair (The switch ... Read more ) took about 20 minutes. The switch ws not the same as the original. Just be careful to mark each wire as you remove them from the old switch's posts. The posts on the switch are marked and you need to place them on the like-marked corresponding posts on the new switch. All is well, my burner is operational.

Turned off circuit. Unscrewed old element. Connected new element and screwed it in. Worked like a charm. It shipped very quickly. Could not be more satisfied; total repair: $30 and prevented me from buying a new oven; satisfaction: priceless.

Open oven door about 3 inches - then holding on the door on either side - pull up and door slides off - put it aside - this is to make it easy for you to work inside oven compartment - at rear of oven where the element goes into the back wall - there are two nuts to remove - I did not have a nut drive so used a pliers (GE could have put s ... Read more lots in the nuts so one would just need a screwdriver) - pull element forward - there are wires attached to the 2 ends of the element - remove with screw driver - element is off - get new part from PartSelect -(and must say pleased with their service) - and reverse above procedure.

1. The infinite switch had several knobs which would fit the switch shaft. Read the directions included with the switch in order to have the shaft fit the proper knob. You can break the shaft with two pairs of pliers. 2. Move the stove away from the wall and unplug it. 3. Remove the 1/4 screws from the back side of the stove and re ... Read more move the back panel, exposing the switch. 4. Remove the wires one at a time and put them on the new switch. The terminals are L1, L2, P, H1 & H2. The Pilot (p) has a smaller terminal so you don't get it mixed up. Generally L1 is black, L1 is red, P is yellow, H1 and H2 can be blue, brown, yellow, orange or one of these colors striped on a white wire. 5. Remove the old switch from the stove and be sure to save the two mounting screws. 6. Position the new switch so that the side of the switch marked "top" is on top. 7. Install the screws on the new switch and put the knob on it. 8. Carefully test the burner. 9. Unplug the stove and put the back cover on.

Element was easy to remove two screws and unplug it. New element didn't have the same prongs and brace was different. Added ends to plug with screws supplied drilled new holes in oven back for brace. Works fine for a repair by a 65 year old woman.

My sons helped with that. They had to use a pliers to remove the old screws (did not have to notches). After that they they removed the element. Then the wires had to be disconnected (after we unplug the oven from the main power source. Then the wires were connected to the new heating unit. We only got one screw in so far will work o ... Read more n getting the second one in when they return tomorrow. I did turn on the oven and it works!!!

Thank you to the nice young man that helped me on the phone.

First off the part was easy to find on Partselect...

Second point... ordering was easy and shippment was fast thanks to Partselect...

Replacezment was fairly easy useing a Nut driver and a pair of pliers...took about 40 minutes.

Thank you Partselect...

Chuck