EasyApplianceParts is now PartSelect! We've merged our sites to provide a better shopping experience for you.   Full Details

Find Parts

Parts Departments

Top Model Types

Top Brands

Repair Help

Expert Repair Videos

Keep typing for more specific results...

RGJ534GEP1 Hotpoint Wall Oven - Instructions

All Instructions for the RGJ534GEP1
1 - 5 of 5

Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!

Search filter:
Clear Filter
Your search term must have 3 or more characters.
oven door seal was old and falling apart
56 of 67 people found this instruction helpful.
  • eric from washington, DC
  • Really Easy
  • Less than 15 mins
  • Screw drivers
at first thought the seal would just slide out and the same for the replacement. when I realized that this was not the case and began to wonder what....? I saw the screws at top and bottom, took them off and voila the inner shell moved forward enough to take out the old, slide in the new, push in, replace the screws and back to a happy w ife with an oven that can bake correctly again
Was this helpful?
Thank you for voting!
gas valve quit working
1 person found this instruction helpful.
  • chris from FORT BRAGG, CA
  • Very Easy
  • 15 - 30 mins
  • Screw drivers
Very easy, didn't even have to take the oven out of the wall. Will use this site again.
Was this helpful?
Thank you for voting!
the oven seal was dried out and crumbling not safe to use on a gas appliance
1 person found this instruction helpful.
  • jim from SAVAGE, MN
  • A Bit Difficult
  • 30 - 60 mins
  • Screw drivers
From what I was able to find info on I was to take out 5 screws 3 on top and 2 on the bottom then the inner oven box is suppose to pull out a bit to take the old gasket off and put the new onw on the box was so rusty it would not pull out so I was able to get enough of the box out using a large screwdriver the lip of the gasket tucks behi nd the box. I ended up using a small screwdriver to work the new gasket behind the oven box. The door now needs new springs the tension on them is not strong enough to pull the door shut the way it should there's still room to push the door into new gasket.
Was this helpful?
Thank you for voting!
Electronic Control wouldn't stay on
9 of 31 people found this instruction helpful.
  • Russell from Paso Robles, CA
  • Easy
  • 15 - 30 mins
  • Nutdriver, Screw drivers
Unplugged and pulled oven out, removed cover from top, removed control unit, prepared new control unit with jumper and face sticker, transferred wires from old unit to new unit, checked operation of new unit by plugging oven in... wooo hooo it works! reverse above steps... viola... done!
Was this helpful?
Thank you for voting!
would not heat the ignitor up at all.
  • Gary from yANKTON, SD
  • A Bit Difficult
  • More than 2 hours
  • Nutdriver, Pliers, Socket set, Wrench set
The control kit came very fast only a few days. the instructions were ok but not that clear.....they have u add a jumper wire which is not hard to figure out but the fact that they say nothing about what wire needs to go from the other side of the relay. they say the yellow wire needs to go to no(the other lead on the relay)and that was n ot the case for my setup.i had to run my ornge wire from the ignitor to that side of the relay to get it to work when the instructions say to connect the sensor harness adapter to the same wire colors which had an ornge wire in it.so that was the only part that did not make sence. but other than that it works great.
Was this helpful?
Thank you for voting!
All Instructions for the RGJ534GEP1
1 - 5 of 5