RGBS100DM2BB General Electric Range - Instructions

I thought I was being a total girl and was afraid of fixing my oven myself, but when it took forever to get my landlord to come over and fix my oven I ordered the part, got it in three days, followed the directions online and fixed it myself! Easy, easy! Turned off the electric, switched off the gas, unscrewed 2 bolts, unplugged the old s ... Read more witch, screwed in the new switch, replugged it and turned on the stove. Roasted a chicken and baked bread within minutes!

I deturmined that the flame starter was not pulling enough amps to open the gas valve (safety valve) . pulled two hand screws and removed floor of oven exposing the flame bar and flame starter. removed two screws on flame starter. removed lower pan drawer and disconected the electrical plug for flame starter. replaced in reverse orde ... Read more r. easy.

I found that it was a little easier to pull out the stove to do the electrical connections. First I pulled out the stove being very careful not to bend the gas line. I pulled out the wires and disconnected them. I removed the 2 screws that hold the igniter and compared it to the new one it matched. I hooked it back up with the 2 screws th ... Read more en did the wire connections pushed the stove back carefully and tested the new igniter it worked like new no more microwave dinners thanks parts select .com

Removed the screws that held the shield in place. Then unplugged the igniter and removed the 2 screws that hold igniter in place. I had to cut the connector off the new igniter and wire nut the old connector on because of a different connector.
I then put everything back together and ooolaalaa, it worked!!!!!!!

Thanks for ... Read more the quick service,
Tom

had to take back off of oven because of the connector and the plug end insert had the wrong pin so i had to take it apart and use old ones then i put the assembly in /and put oven back together

First I removed the botoom drawer.
Second, removed three 1/4 in (head size) screws and removed the reflector pan from the bottom of the oven.
Third I removed the three racks in the main part of the oven and then the two slot head screws that retain the oven floor. I then removed the oven floor.
Four, now that I had access t ... Read more o the ignitor, I removed the two 1/4 (head size) screws that mounted the ignitor to the burner.
Fifth I disconnected the wire plug which is located in the lower section of the oven. I was unable to route the wire with it's connector on out of the oven, so I just snipped the wires and took it out in two pieces.
Installation was just the reversal of this with the obvious exception of snipping the wires. I was able to route the wires differently so that I did not have to pass the connector behind any restrictions.
Finally afte all was reassembled, I did an ops check and everything worked just fine.

remove the door,racks,cover over burner,burner,element,replaced element and rest in reversed order.

I didnt you stupid fu ks sent me the wrong oven door hinges now my wife is pissed and filling fot a divorce..thank you guys so much fot not knowing the proper product number or sending the right parts

To get to the element I had to remove the lower cover from inside the oven.

After that I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the wires. The wires are accessible from behind the undertray.

Installation of the new one was simply the revers ... Read more e.

Before re-installing the burner cover I did a quick test to ensure the new igniter functioned properly and that I hadn't mis-diagnosed the problem. The element quickly started to glow and that was it.

The oven now works as it should.

Simply took out old burners replaced them with new burners, no tools needed.

Ordered part from customer friendly Part Select and received the replacement part within a few days, and installed it promptly. Wife is happy and stopped grumbling about oven bottom unsightly defect! Small price to pay for a happy wife! Ernie

placed on range

Just lifted off the old burners set on the new ones.

Remove interior bottom of oven, remove igniter screws, unplug igniter. reinstall igniter.

Simply removed old burners. Placed leveling nuts in place. Replaced new burners in place.