Home
RGB790DEP4BB
Instructions

RGB790DEP4BB General Electric Range - Instructions

All Instructions for the RGB790DEP4BB

Ignitor would glow, gas valve would not open

1 person found this instruction helpful.

Arthur from Saint Francisville, LA
A Bit Difficult
15 - 30 mins
Nutdriver

This web site is awesome!!! their forum told me what part i needed, and they shipped it out, super fast, i couldn't hardly believe it! I tried using the Sears Parts web site for my "kenmore" oven and that was a joke, seriously! no more kenmore for me, thanks. It took this site to figure out that i really had a G.E. with a kenmore na ... Read more

Read less

Was this helpful?

Over not lighting

1 person found this instruction helpful.

Anthony from DeKalb, IL
A Bit Difficult
15 - 30 mins
Nutdriver, Screw drivers

Remove the front door-lifted off(no tools) removed the floor of the oven (2 standard nuts at the rear). nut driver to remove the igniter. Took longest to untwist and retwist wires & dropped screws. reassembled and tested...worked perfice. this is the 4th time I've used Parts Select and It's great....Thanks and keep up the good work!

Was this helpful?

Oven would not light

1 person found this instruction helpful.

Roger from Downingtown, PA
Really Easy
15 - 30 mins
Screw drivers, Wrench set

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cov ... Read more

Read less

Was this helpful?

broiler woks ,bake doesnt

1 person found this instruction helpful.

HEIDI from NEW ROADS, LA
Easy
15 - 30 mins
Socket set

i went for 3 months waiting on the electrician who never came then asked the plumber who else could fix it and he said my husband could it only needed to unscrew 4 tiny screws and unplug and cut and twist wires back the hardest part was reaching the bolts hooked to the ignighter the burner was in the way and is not as easy to remove as so ... Read more

Read less

Was this helpful?

Broil would work, but bake wouldn't

1 person found this instruction helpful.

Patricia from Bellevue, WA
Easy
15 - 30 mins
Nutdriver, Screw drivers

IThe schematics on the website were helpful for how everything goes together. I just followed the picture and then unscrewed all the screws that held the ignitor to the gas pipe. Have to pull out the gas pipe out first so you can get to the bolts, easy to do when you pull out the drawer and unscrew the hold down for the gas pipe.
< ... Read more

Read less

Was this helpful?

Oven wouldn't heat

1 person found this instruction helpful.

ERIK from MADERA, CA
Really Easy
15 - 30 mins
Nutdriver

I removed the bottom pan and then removed the flame extender to get access to the igniter. I removed the two screws and cut the wires. I then wired the new igniter and used the ceramic wire nuts that came with the part. After that I installed the igniter. It was very easy to do this repair.

Was this helpful?

The Igniter Would Not Glow To Ignite The Gas

1 person found this instruction helpful.

DUANE from BROOKFIELD, WI
A Bit Difficult
15 - 30 mins
Nutdriver

Remove the broiler pan to get at the 2 nuts that hold the gas burner, remove them and then you can get at the 2 nuts on the back side of the igniter.

Was this helpful?

oven wouldn't heat

1 person found this instruction helpful.

Josephine from Hawthorne, NJ
Really Easy
15 - 30 mins
Pliers, Screw drivers

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

Was this helpful?

Replace igniter

1 person found this instruction helpful.

Miguel from Burlingame, CA
Really Easy
15 - 30 mins
Pliers, Screw drivers, Socket set

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

Was this helpful?

Igniter wouldn't turn on to ingnite the oven

1 person found this instruction helpful.

Peter from Lyndhurst, NJ
Easy
15 - 30 mins
Nutdriver, Screw drivers

It was a simple repair removed the oven door, and the oven bottom plate. removed the screw that held the burner tube to gain access to the two screws that hold the igniter in place clipped the wires. put the new one on with butt end wire connectors instead of the wire nuts supplied. screwed the igniter back onto the burner tube put the bu ... Read more

Read less

Was this helpful?

Gas oven would not light

1 person found this instruction helpful.

Dwight from Houston, TX
A Bit Difficult
15 - 30 mins
Nutdriver, Screw drivers, Wrench (Adjustable)

I was able to access the burner and igniter by removing the broiler drawer. The flame guard was removed with a nut driver and the old igniter with a phillips screwdriver.

The electrical wires had to be spliced into the old igniter wires as they did not come with the factory connectors. However sire nuts were supplied.
... Read more r />After replacement of the igniter with the new one .. it would glow and about a minute later the gas would come on. However the gas from the burner did not light. I had to adjust the bracket closer to the burner to correct the issue.

Note: The igniter is wired in series with the gas valve. This means that it will continue to glow even after the burner lights durning oven operation.
Read less

Was this helpful?

Thank you for voting!

Oven did not light

1 person found this instruction helpful.

Steve from Houston, TX

Really Easy

15 - 30 mins

Nutdriver

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

Was this helpful?

Thank you for voting!

The old burners were damaged by the prior owners.

1 person found this instruction helpful.

Mohammad from BARTLETT, IL

Very Easy

Less than 15 mins

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Other Parts Used:

Burner Head - Medium - 9500

Burner Head - Large - 12K

Was this helpful?

Thank you for voting!

Burners wouldn't light

1 person found this instruction helpful.

Robert from SOUTH ELGIN, IL

Very Easy

Less than 15 mins

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

Other Parts Used:

Burner Head - Large - 12K

Burner Head - Medium - 9500

Was this helpful?

Thank you for voting!

The light inside the oven had burned out

3 of 7 people found this instruction helpful.

Catherine from SEATTLE, WA

Very Easy

Less than 15 mins

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.
Read less

Was this helpful?

Thank you for voting!

All Instructions for the RGB790DEP4BB

91 - 105 of 307
Prev
1
...
5
6
7
8
9
...
21
Next