RGB745EEHDBB Hotpoint Range - Instructions

My husband removed the two screws t hat hold the element in place, Then he pulled the element out about 3 inches and disconnected the two wires and replace the element with the new igniter put everything back and now its working like a charm

First shut down electric power to oven. remove
oven racks and botton tray. Removed boiler rack and door. Next unscrew 2 bolts holding igniter. remove nuts or cap for two white electric wires.
installed new igniter, hooked backup wires. replaces racks and tray and that was it, job done.

Removed the bottom plate inside the stove by removing two back screws. The burner was exposed. roved a total of three screws on gas burner to remove the entire assembly. Removed two screws from the old igniter and then put new one on. Save the old connectors because they have unique connectors. Cut old wire and strip 3/8 inch of wire cov ... Read more er off. Using the supplied wire nuts. Caution use only supplied wire nuts because they are meant for heat. connect old wire to new wire of the new igniter. Reverse order of screws that you did for the job. That is it

I figured out the problem, ordered the part, and replaced it. Four hex head screws, two wire nuts, and two thum screws latter it was working.

I removed the bottom pan and then removed the flame extender to get access to the igniter. I removed the two screws and cut the wires. I then wired the new igniter and used the ceramic wire nuts that came with the part. After that I installed the igniter. It was very easy to do this repair.

Unplugged the oven. First i removed the 2 screws from the pan at the bottom of the oven and took the pan out. Next i took out the drawer underneath and took the screws out of the pans below to get to the ignitor. Unscrewed the ignitor and cut the wires below it to splice the new ignitor on. Spliced the two sets of wires and put the cerami ... Read more c wire nuts on. Replaced the top and bottom pans and put the drawer back. plugged the oven back in and started the oven right up. Pretty easy.

i followed the same directions others had posted - good tip to remove the oven door for easier access - i was nervous about stripping the wires to splice together, so i made my hubby strip the wires for me :) - did all the rest myself. no trouble at all - if a girl can do it, anyone can do it!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...And then I installed
ignitor tightening the two screws and connected the two ignitor wires with the provided wire-nuts.
Mike Polcho

I frist remove the screws that hold the element in place disconnected two wires.That didn't take long.Call aronud my area for part.They wanted 90.00 plus taxs.Went on line to find it much cheaper came in the mail very fast and put it in my self.Very easy and saved money too.It took less then 3 mins to put in.If I could do it you can too.T ... Read more hank You,Bearice & Robert Reynolds P.S works great and no yelling at each other.Easy

well first off I repair commercial HVAC equipment for a major drug company so I think I've done it all.I thought it cant be much different than any burner assembly.I made it harder than it had to be,anyone can do this.I removed lots of unneccessary things.Let me help you only take out the drawer on bottom of stove.so I started on top and ... Read more worked my way down.save time and open the stove to were the door stops then have faith and give a good yank.this will remove the door,dont be afraid it will go right back on those two hinges easy.now that this is out of the way remove the bottom plate that covers the burner assembly (2 screws)in back pull it out then you see the igniter.as I said before with drawer pulled out remove the 2 1/4"nuts screws holding it up then from bottom.Unplug this stove then remove the 2 places its plugged in to.after you remove this there are 2 screws that hold it into the igniter remove them .cut the wires with enough room to re use the plug ends.strip the wires and use the wire nuts that they provide then put back together with new wires on new igniter then.re attach.put everything back together in the reverse order you took them apart.plug in stove and see the igniter light up again and light stove.do not call repairman you can do this.save your money for you its bad enough you have to buy anything else.

Removed grills, oven bottom, heat deflector, and the two igniter mounting screws. Pulled out igniter, removed two wire twist caps and old igniter. Cut off ragged ends of wires coming from the stove side and re-stripped the wire ends. Attached oven side wires to new igniter wires using new twist caps. Reassembled everything in reverse ... Read more order. Tested oven operation to ensure that the gas ignited promptly. (It did).

First I disconnected power, then removed two screws from igniter & cliped two wires. Then installed new igniter & with the wire nuts supplied refastened to supply lines in oven.
PartSelect makes repairs quick & easy. It just takes a little smarts on your part.

No job here. . . . Just sat new parts on to replace old ugly parts.

Remove rear cover. Remove old display. Remove one wire (and place on new board) at a time. Carefully remove faceplate from old board and place on new one. Close everything up and your done. Took 10-15 minutes.

changed double burmer pans