My Orders
- Home
- RGB533DEP2CC
- Instructions
RGB533DEP2CC Hotpoint Range - Instructions
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
I had recently found out I was expecting, so had to drop the cigarettes... needless to say I threw a hissy fit 2 days in and sadly our range door got shattered in the process. Luckily my honey was able to repair this with little to no cussing occuring!
5 of 5 people
found this instruction helpful.
-
Linnea from Mankato, MN
- Easy
- 30 - 60 mins
-
Screw drivers
We had to make sure every bit of broken glass was removed - then removed the outer cover of the door, inserted the new pane of glass, and screwed the cover back on. Over all, pretty easy. (Especially for me!)
Was this helpful?
Thank you for voting!
Needed To Replace Burner
5 of 6 people
found this instruction helpful.
-
Robert K from York, PA
- Really Easy
- Less than 15 mins
Took longer to open the box.
Was this helpful?
Thank you for voting!
Burnt burner
7 of 12 people
found this instruction helpful.
-
Janine from Wind Gap, PA
- Really Easy
- Less than 15 mins
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Was this helpful?
Thank you for voting!
Oven would not turn off due to inoperative thermostat
7 of 13 people
found this instruction helpful.
-
Timothy from Lake Elsinore, CA
- Easy
- 15 - 30 mins
-
Screw drivers
1st ensure thermostat is intact, I thought it was broken but upon further investigation I noticed that one of the screws that hold the thermostat in place had came loose which cause the thermostat knob not to be able to turn the thermostat stem. Re-installed thermostat mounting screw and it worked just fine.
Was this helpful?
Thank you for voting!
old blackened oven racks
8 of 17 people
found this instruction helpful.
-
Roger from Falls Church, VA
- Really Easy
- Less than 15 mins
Replaced old with new.
Was this helpful?
Thank you for voting!
none
3 of 3 people
found this instruction helpful.
-
Michael from Laughlin, NV
- Very Easy
- Less than 15 mins
slid the old ones out and slid the new ones in. done
Was this helpful?
Thank you for voting!
Burner on stove not working correctly
4 of 6 people
found this instruction helpful.
-
Trevor from Eldersburg, MD
- Really Easy
- Less than 15 mins
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this helpful?
Thank you for voting!
Oven ,Going on/off intermittently" Very Dangerous during day /at night especially when all is asleep /away from home,not knowing!
4 of 6 people
found this instruction helpful.
-
Leroy-Anthony from Jamaica, NY
- Really Easy
- 30 - 60 mins
-
Nutdriver, Screw drivers
To: Remove.Four(4)nuts. Six(6)screws. Two (2) clips. To:Reinstall reverse process. "Very simple stright forward, and most enjoyable."
Was this helpful?
Thank you for voting!
No oven
4 of 7 people
found this instruction helpful.
-
Robert from SAUGERTIES, NY
- Really Easy
- 15 - 30 mins
-
Nutdriver, Wrench (Adjustable)
Hired gas company to do repairs for safety reasons
Was this helpful?
Thank you for voting!
No ignition
6 of 14 people
found this instruction helpful.
-
Karen from Dale City, VA
- A Bit Difficult
- 30 - 60 mins
-
Socket set
The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had t
... Read more
o cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!
Read less
Was this helpful?
Thank you for voting!
Digital clock no longer worked
2 of 2 people
found this instruction helpful.
-
Dolores from AVOCA, IA
- A Bit Difficult
- More than 2 hours
-
Screw drivers
No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.
Was this helpful?
Thank you for voting!
The eye would not light
2 of 2 people
found this instruction helpful.
-
Solomon A from COLLEGE PARK, GA
- Really Easy
- 30 - 60 mins
Remove the existing burner and install the replacement.
Was this helpful?
Thank you for voting!
The burner caps were chipped and discolored.
2 of 2 people
found this instruction helpful.
-
Anne from OSSINING, NY
- Very Easy
- Less than 15 mins
I merely replaced the old caps with the new ones. It couldn't have been easier!
Other Parts Used:
Was this helpful?
Thank you for voting!
oven racks very old and writing on knobs worn ff
2 of 2 people
found this instruction helpful.
-
Patricia from SAN JOSE, CA
- Very Easy
- Less than 15 mins
Very was ti replace racks and knobs. Very fast mail service
Was this helpful?
Thank you for voting!
Burner had uneven flames
3 of 5 people
found this instruction helpful.
-
Akshay from Bridgeton, NJ
- Really Easy
- Less than 15 mins
Too easy a five year old could do it
Was this helpful?
Thank you for voting!