RGB533DEP1CC Hotpoint Range - Instructions

Remove the existing burner and install the replacement.

The repair was somewhat easy, it would have been easiere if I had figured out the right part in the first place! Replacing the Thermostat is a simple task and actually only took abut 10 minutes. The harder task was replacing the glow bar in the broiler area! What a pain! The part had the same gender connector as the existing wiring. Had to cut the connectors off and use ceramic wire nuts... should be simple but the wires on the replacement part were about 1/2 inch too short! After some creative manuvering and about an hour of cussing out the OEM part manufacturer it went together and worked OK but I suggest before trying to solve a problem like this remember the basics... always check the obvious first!

No longer carry the one to our stove so it was substituted with Nafisa on it. You could see all the electronics so we had to pry the old face off the old one blew it in place, but a clock was reversed from timer, but it works.

This gas range had an oven that would heat, but it wouldn't hold it at a stable temperature. Say you set it at 300 degrees. Well, it'd head up to broiling temperatures, then drop down to like 200 degrees, then 400 degrees (You get the picture).

My guess was that the thermostat, given that this oven was ~20+ years old, was no longer able to detect correctly the temperature inside the oven.

The thermostat sensor is made up of the housing (The part that sits behind the oven temperature control knob), a long wire (so you can route it to the inside of the oven), and the probe itself (Which I boldly assume is the thing that measures the temperature inside the oven)

TL;DR:

-Pull oven from wall.
-Turn off electric and gas.
-Remove the grates and drip pans off the top.
-Pry the range's cooktop up (It's on like a hinge and is designed to lift up. You have to play with it a bit with like a screwdriver on the sides (One on each side). If you pry just a tad, you'll notice these prongs that act like detents. (LIFT CAREFULLY, the heating elements are still connected via their gas lines! They're flexible, but don't man handle the thing!
-Once that's up, it's time to finally start removing the thermostat which is the knob that controls the oven temperature. Pull the plastic knob off which will expose the two screws you need to detach it from the oven (Phillips head). Be super careful. You don't want to drop these screws. You'll be struggling to fish them out of the empty space that sits between the thermostat and plastic knob.
-Once that's loose, open the oven door and detach the thermostat from the back of the oven. Recycle the prongs holding the old thermostat sensor for the new one.
-Go to the back of the range. Like the actual back part of it.
-Frustrate yourself with pulling out the thermostat through the route it's been put in. It's difficult to route it through the tight spaces, but not complicated. Keep a mental note of this route and copy it with the new thermostat that you have to install.
-Don't fret, when it comes time to wire the new thermostat sensor, it's actually a lot easier than you would think to find that little hole in the back of the range that you have to slot it through. It's just slightly covered by insulation. Pulling it slightly aside, you'll see it very easily.
-Screw in the thermostat housing at the front of the oven.
-Frustrate yourself again by routing the wire while taking care not to bend the probe (This is my assumption not to bend it and I think it's a safe assumption to make)
-Find that tiny little hold in the back of the range again, insert the probe through it, then use those recycled prongs to hook that probe into place.
-Yay, you're almost done.
-Reinsert knob on thermostat.
-Turn gas and electricity back on.
-Give it a test run to see if you did it right.
-if it still doesn't work, then it might not have been the thermostat giving you problems.
-If it does work, put everything back the way it was.
-You're done.

Followed you tube instructions I found on line via parts select recommendations.

the electrodes on this model have to be removed before you can raise cooktop, once cooktop is raised remove wire from burner bracket, use needle nose pliers to squeeze bottom of clip,remove &replace with new parts.

Super easy for me! My son-in-law is a contractor, I gave him the parts and let him do the work.

I put it in the same way tuck it out

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

Start by shutting off the main gas supply to the range and unplugging the electric cord.
You will first need to take the plastic control knobs of from each individual burner (they should slide straight off).
Next, you will need to remove two phillips head screws on the front face of the panel. They are located on the right side of each rear valve burner stem that is sticking out through the panel.
Next, open the oven door, locate and remove the three screws on the bottom of the front face panel. The front panel should now come off exposing the top burner manifold and all of the valve burners.
The next step would be to take the burner grates and each round burner cover off (no tools required). This will expose the top of each individual burner. You will see screws that hold each individual burner down to the stove top. On my stove the heads were all rusted and I could not remove them. If you can remove all four of your burners and disconnect the wire on each ignitor and set the burners aside.
Next, go back to the front of the stove where you took off the panel and you will see two metal clips on each side of the stove top. Push each one of these in with a screwdriver and gently lift up on the stove top. It should hinge up towards the back of the stove and give you full access to the burner valve you need to change.
Next, use a box end wrench (I think it was 1/2") and remove the gas line attached to the burner valve. After the gas line is removed, take out the bolt and clamp that holds the burner valve to the manifold. The old valve should drop out.
Install the new valve making sure the rubber gasket is seated properly, reattach the clamp and bolt and reinstall the burner tube line.
Before you put the range all back together turn the gas back on at the appliance shutoff. Locate the gas orifice for that particular burner and hold your thumb or finger over the hole. Turn on the burner and leak test the burner tube connection and where the valve is clamped into the manifold.
Shut the burner back off if the leak test passes and reassemble the stove.
If your burners won't come out of the stove because the screw heads are rusted off (like mine was), you can carefully lift the lid a couple of inches to gain access to the valve. Make sure you don't bend or kink any of the burner tubes.

My husband and I probably could have done the repair in 15 minutes except for the difficulty lifting up the range top, dropping the screws into the range where they could not be retreived, threading the thermostate into the little holes from the top to the inside of the oven and then trying to hook the range top back into place. Even with all the difficulties we still accomplished the task in one hour. Thank goodness we had 4 extra screws that worked (actually only takes 2 but of the 6 we had, 4 fell into a place you could not reach into). Glue on the end of the screw driver finally kept the screws from falling into the black hole. It was an adventure and would do it again.

1. Open oven door
2. insert oven racks (perfect fit)
3. close oven door. Done and finished - man am I tired

The repair was extremely easy. Just removed the old burners and dropped in the new ones. No tools needed.

Had two burners on the stove that would not light. Had tried cleaning them but they still did not ignite. Replaced both burner heads. Once replaced. they ignited right away and have worked ever since.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.