RGB524PPHC General Electric Range - Instructions

ordered parts, 2 double burners, 3 days later they arrived.opened box.
lift stove top, lift out old burner,placed next to new burner to see if they were the same. THEY WERE. place in new burner, checked to see if burner assembly fit correctly. IT DID.
units purchased were exact replacements. supplied spacer nuts not needed.
... Read more >easy fix looks new again, thanks.

Lifted the top and dropped in the new burners. Realized they always should have had the leveling washers provided so I took the burners off, dropped on the leveling washers and dropped the burners back on. This all took about 2 minutes. Really made the range top look a lot nicer.

I removed the original gasket clips with pliers. I installed the new gasket by aligning the clips with the holes around the door and pressed into place. Easy fix!

slid the old ones out and slid the new ones in. done

First just unscrew each natural gas jet and install the propane jets. if they are hard to come off just turn your wrench back and forth first until the jet turns with your fingers. Then open the oven and take out the racks. In the bottom back of the inside of the oven there is a screw on each side. Unscrew both screws lift the bototom pla ... Read more te of the oven and slide it back about 1/2 inch then lift out of the oven. Move the 1 screw covering the heat shield from the oven jet. Then light the top burners and turn them off just to get the gas flowing. Also light the pilot in the oven, then light the oven. To convert the oven from natural gas to propane all you have to do is adjust the jet while the oven is lit. turn the oven jet ubtil there is a blue flame with little or no yellow tips on the flames.

One of the initial two screws for the oven bottom would not budge. Finally used a socket set to loosen it up. Upon taking out the old bottom I turned it over & saw a heat shield attached. I have no idea if you can order a new bottom with a new shield already attached or not, but I had no idea it was there until I took the old part out. Ou ... Read more t of the eight screws attaching the shied, four of them were also difficult to loosen up. But in the end the new bottom looks great !

I moved to an apartment where the past tenants did not take care of the stove. I think this stove is 10+ years old and looks like it was never cleaned in all of its existance! I cleaned everything really well with oven cleaner and lots of scrubbing. The stove looked brand new except the burners! I couldn't take it anymore so I ordered n ... Read more ew ones. The burners came in less time than stated. I opened the box, took the burners out, lifted the oven hood and just placed them right where the others were. There are no tools needed it pretty much just gets placed down in the appropriate spot and that's that! No directions or tools needed. My stove looks awesome now!! When you first use the burners, you will probably need to place a match or lighter by the burner to get the fire going. After that, it lights perfectly every time.

Popped off old gasket and some retaining clips stuck but were easily removable. New gasket pops right in, super easy. Fits like new.

Found the Model information under the bottom drawer. Googled GE Range and rubber, found this vendor. Amazing, the replacement gasket was exactly as the original. Took the old gasket off with needle nose pliers, there were small metal clamps that had to be pinched together. Once the old gasket was off, the new one practically installed ... Read more itself. Woman Power!

Baking is MUCH better now!

Removed two screws to remove old bottom. Insert new oven bottom and re-attach screws.

Very was ti replace racks and knobs. Very fast mail service

Ordered the part and put it on. My husband hasn't relized that i took care of it yet. One day he might remember to ask if we ever got the part. Very quick delivery.

Took it out of the box, lifted the stove lid and replaced the part, no tools required. Very satisfied with the shipping and the part, great service. Thanks!

Two set screws in rear; removed easily with a screwdriver. Old oven floor lifted out easily; new oven floor dropped in just as easily; set screws re-installed. Done. Pleasantly surprised at how easy this went.

Simply took out old burners replaced them with new burners, no tools needed.