RF764404 Hotpoint Range - Instructions
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Element burned out
Partselect had the right part, clearly indicated in the diagrams and menus. Shipped quickly. Easy to use web site.
Parts Used:
-
J. from Durham, NC
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
2 of 7 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
original trim rings
replace trim rings with the new shiny ones I got from parts select. Thank you!
Parts Used:
-
larry from fort wayne, IN
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Old Burner was crappin' out after 20 years of service
Pulled out the old burner that was held in by a metal spring clamp. Pushed the new one in.
Good as new.
Good as new.
Parts Used:
-
Jay from Madison, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The old surface unit was not generating heat
We just remove the old surface unit and insert the new one by hand. Thanks to PartSelect, we were able to buy really good quality part that works right away! It was a 26-year-OLD GE Stove/Microwave space maker, the parts were hard to find in stores. Thank you for selling this! All the best for your business!
Parts Used:
-
Yi from Miami, FL
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 1 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
I needed new trim rings around the stove burners
I logged into GE's website, put in my stovetop's requirements for size and type of trim rings, and was taken to partselect's site where I found what I needed. I ordered it and it came in less than a week!
Parts Used:
-
KoLynn from Tempe, AZ
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
drip pan, trim ring were old and burned
just replaced the old for the new
Parts Used:
-
Preston from cincinnati, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
0 of 2 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
instructions could be better
it was hard to figure out the instructions from A switch to B switch to my switch. The first switch was no good the second one was good. prayer book didn't hurt.thank
Parts Used:
-
WILLARD from GLOVERSVILLE, NY
-
Difficulty Level:A Bit Difficult
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
0 of 6 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
burner pilot light out
Replaced neon light and jewel plastic. Had difficulty installing the neon lamp unit on the existing clip but other than that the repair was uneventful. The parts furnished were the exact parts needed!
Parts Used:
-
Ted from Midland, MI
-
Difficulty Level:Easy
-
Total Repair Time:30 - 60 mins
-
Tools:Pliers, Screw drivers
0 of 12 people
found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Plastic Insert for knob to long, had to use my bench grinder to cut it down
(Turn off the Power) Pull stove out, remove the 2 screws that holds switch in place, remove one wire at a time and install on new switch. Slip switch in replace 2 screws. Snap off about 3/4 of the shaft cut down plastic insert for knob, install knob turn on power and it works.
Parts Used:
-
Floyd from Warren, OR
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
rht. front element would not heat properly
I read parts select instructions and i was done in less than 30 minutes. Since 1988, this is the 1st. part that I had to replace. I now have parts select on my favorites list.
Parts Used:
-
Rod from Huron, OH
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
element heat wouldn vary
slid the range away from wall. disconnect power. removed back,compared switches and marked wires.installed new switch and wires.the adapter for the control knob was a problem it left the knob out futher than original i had to modify the plastic adapter and got it close enought! the most time spent was cleaning up the floor before putting the range back.
Parts Used:
-
Leonard from Winter, WI
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver, Pliers, Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Old very stained drip pan and rings
Simply removed old and inserted new. No tools necessary.
Parts Used:
-
Avril from Wasilla, AK
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
Was this instruction helpful to you?
Thank you for voting!
broken light socket
The only tool needed was a nutdriver to remove the lamp socket. I needed my head mounted light to see what I was doing, and everything went smoothly from there. Simple job.
Parts Used:
-
James from Monterey, TN
-
Difficulty Level:Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Nutdriver
Was this instruction helpful to you?
Thank you for voting!
Element burned into.
TURN POWER TO OVEN OFF AT POWER PANEL 1- Remove element: 2 screws ... cut wire at element because of burned area. 2- Crimp two new wire lug connectors onto wire and attach to new element with supplied screws. 3- Attach element to back of oven: 2 screws ... TURN POWER ON AGAIN AND TEST OVEN
Parts Used:
-
Erbin from Poquoson, VA
-
Difficulty Level:Really Easy
-
Total Repair Time:15 - 30 mins
-
Tools:Screw drivers
Was this instruction helpful to you?
Thank you for voting!
Oven light wire broken, damaged socket
Remove light bail, glass cover held by two nut screws. Pull socket, removed clips in back, replaced wire connectors, placed new socket in, then glass cover and bail. Wire connected in back, cover plate replaced.
Parts Used:
-
Patricia from Brandenburg, KY
-
Difficulty Level:Really Easy
-
Total Repair Time:Less than 15 mins
-
Tools:Nutdriver, Pliers
Was this instruction helpful to you?
Thank you for voting!