RF43*T1 General Electric Range - Instructions

Before you start, make sure the circuit breaker is not tripped, which can explain element not heating.
In my case, the toaster element was ok, which tells us that the oven is receiveing electric current.
1) Take the grills out so you have free access
2) Remove the door - this model just pull it up to let it free
3) rem ... Read more ove the 2 screws securing the element on backwall of the oven and gently pull the element out
4) if you have a multimeter:
a) set it to AC, greater than 300 V
b) use your alligator clips, attach the clips
to the contacts of the element
c) briefly turn the oven on: expect to read between 230 and 260 volts
5) remove the screws securing the old element
6) install the new element;
7) secure the element back to the backwall
8) turn the oven briefly on and feel the heating element: should come warm pretty quic;
- Job done -

When you remove the screws securing the wire to the old element, make sure the wires are not cracked, or interrupted.

Otherwise, a real simple and easy fix.

Specs of this element are what I missed but here they are:
Resitence : 25.5 Ohms
Volts: 230 - 260Volst
Power : 2050 to 2650 Watts
The power depends on the voltage, so make sure you dont have it too low (less than 220 ) or too much (yeah, 260V is nearing upper limits)

Finding the replacement part on partselect.com was easy. The search feature brought me to a diagram of the bake element and offered precise grid measurements to assure me it was the correct part.

Be sure to completely unplug your stove before doing anything. The only tools I used were a small nut driver, a standard pliers a ... Read more nd a flashlight (and a cushion for my old knees, ha).

Installation was easy, but you have to be very careful to not bend the little prongs were you attach the element to the stove wires... they bend pretty easily, so hold them tight or hold them in a pliers firmly but without crushing them. Drive the two screws to attach the element to the wires; then, drive the two screws to hold the element face plate against the rear of the oven, and viola, you're done!

Thanks, partselect - website, price, packaging and shipping were perfect! Also, I got several good tips from the feedback of other customers that were very helpful. That is a nice feature of your website and a good customer service.

I removed the screw holding the tilt mechanism to the range top. Removed the clips holding the block together. Disconnected the two power leads on the old burner and replaced with the new burner. Closed the block around the leads. Screwed the tilt mechanism back to the range top and that was it!

Removed two clips that held the ceramic insulators in place. Removed two screws that held conductors to the burner. Replaced screws onto new burner unit, replaced ceramic insulators. Fastened clip to burner onto the range. Turned burner on and it worked great. Thank you for your quick responce to my order.

Removed trim ring and drip pan, loosened retaining nut and replaced the burner. I was very impressed at the fast service from your company. Thank You

Removed the plug from wall socket.
Removed door to oven by lifting it straight up while partially open, in locked position.
Remove Baking shelves.
Removed 2 screws @ the back of element where it goes into the ovens back wall with a nut wrench and gently pull the element towards you until wires are exposed.
Using a flat ... Read more blade screw driver hold on to the end of the element near the end with the screw and support it as you un screw the wire so the end of the element does not bend as you turn the screw.
After both wires are removed, remove the old element.
Install the new Element in reverse.
Very Easy!

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. connected the wires to the new element. pushed the element back in place the screwed it back to the back of the stove.

Replaced the burner. Still no heat. Decided to take the front off and test the connections (Power Off!). Found no output from switch to burner. Ordered new switch from PartSelect. Switch arrived in 24 hours, just like the burner (I'm in FL, but still fast!) My only problem was that the know didn't quite fit -- too long. Cut the meta ... Read more l correctly, but still too long. Had to cut the plastic adapter slightly. Now it fits like the others, but it's not quite as secure due to shortening the piece that slides on the metal shaft.

Took Switch panel off range. Disconnected Infinite switch. Reinstalled infinite switch.. Replaced panel. Repair was very simple and self explainatory.
Knott County Housing Authority Maintenance Personnel

Shut power off. Removed two outer screws, pulled heating element forward and removed two more screws. Ordered part and it arrived in three days. Installed in reverse order of removal. Easy fix. Cost was reasonable.

Before ordering the new part, made sure the problem was the burner and not the wiring in this very old stove by putting an ohmmeter on the terminals of the burner after removing it. Since it showed no conductivity, the burner was bad (could have put the voltmeter on the wires and turned on the power to ensure power was coming in......bu ... Read more t did not want to mess with 240 volt/high amperage. With power off at the breaker, installed new burner. One caution... since the wire on the burner terminals is pretty soft, don't bend them by putting too much torque on the screws. This turned out to be my only problem.....I had to clean up the screws and work them through the copper terminals with the burner outside the oven before attempting to screw them on the wire connectors in the oven. Not a big problem, but if you bend the terminals too much when you install the burner in the oven, you run the risk of shorting them together, or breaking one. And that would be a big problem.

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Removed screws that hold element in place. Disconnected the two electrical leads. Put the new element in place, hooked up the two leads and installed the the screws that hold the element in place.

Because of the age of the oven it took a little time to loosen the screws that held the element in. Once the screws were removed it was a matter of pulling the element out about 3 inches and disconnected the two wires, then it was a matter of repeating the steps in reverse. Very quick and easy

First I shut off the range breaker in the main electrical panel. I slid the oven door off for easy access to the back of the oven. I loosened the two hex head screws holding the element to the oven wall. I pulled the element forward to reveal the two hex head screws holding the wires to the element and removed the old element. I attac ... Read more hed the wires to the new element with the hex head screws, fastened the element to the oven wall, slid the oven door back on, and flipped on the breaker. I gathered up my tools and left the apartment. It took me longer to get to the apartment and back than it did to do the repair. PartSelect.com got the part to me within two days of my order, and for six dollars in shipping that's great.. PartSelect.com has been added to my internet bookmark.