RF4287HARS Samsung Refrigerator - Instructions

This company has everything!! One simple spring was all I needed. Fast shipping and product was exactly what they said I needed. Took me less than a minute to fix!! I’ll definitely shop here again!!

Went on the Internet to find the installation instructions.

Really nothing to say simply replace the old spring with the new one and it’s as good as new

Used pliers to put new spring in place;
Time took about 3seconds and I’m a female. Video provided very helpful.

I am 70 and identified the problem and ordered the part. I watched a video lots of times that showed how to... slowing it down to catch details.
It is very easy... and the only problem was that when you are trying to get the assembly out you need a lot of hand strenght that I don't have.
My son easily wriggled and loosened it an ... Read more d out it came. Plug in the wires and pop the new unit in.
Two hours later I heard the delightful sound of ice dropping into the bucket and amazingly the bottom freezer started making ice too!
There is no mention that they are related but it did. We thought the freezer sensor had died but it all works!

You can do it! Best, pb

Called someone else. Got the parts elsewhere.
Got the fridge back online 3 week longer than it should.
got charged for the part then failed to send it.
then finally allowed they didn't have the part in stock.

After purchasing the spring I realized the hinge was the culprit. It has the retainer for the spring as part of it, a small plastic piece that broke off cause the spring to get lost. The hinge replacement was a little more in depth but the video on the hinge is very good and on point.

I removed the old spring along with the sleeve and inserted the new one in its place. used a small screw driver to remove the sleeve and inserted the sleeve side in first. took 5 minutes..

Placed one end of the new spring in left hole and used the needle nose pliers to insert the other end of the spring in the right hole.

Spent a dollar 1.97 on the spring.7.00 on shipping and fixed it in less than 5 minutes.Fantastic

Placed lower spring leg in hole first. Manipulated upper spring leg into upper hole with needle nose pliers.

Held spring with needle nose pliers and slipped into place

replacing broken french door spring.

Prepare the area
Open the refrigerator door(s). Remove the ice bucket/bin by lifting it up and pulling it out (it usually slides forward after a slight lift). Set it aside. Empty any loose ice.
Remove the ice maker cover / upper panel (if present)
There is often a plastic cover or shroud over or in front of the ice maker. G ... Read more ently pull or pry it off using a flathead screwdriver on the release tabs. Some models have screws holding this cover. Note the orientation for reassembly.
Disconnect the wiring harness
Locate the electrical connector (usually a 12-pin plug) on the side or back of the ice maker.
Press the release tab on the connector and gently pull it apart. Do not yank the wires. Tuck the harness aside safely.
Remove the mounting screws
There are typically 2 screws (Phillips) securing the ice maker to the refrigerator wall or bracket — one on the side/top and possibly another. Support the ice maker with one hand while removing the screws so it doesn’t drop.

Remove the old ice maker
Carefully tilt and pull the unit forward/out. It may have tabs or hooks that need to be released. Wiggle gently if stuck. Avoid forcing it to prevent breaking plastic parts or damaging the fill tube.

Install the new ice maker (DA97-07365G)
Position the new assembly in the same orientation. Align any tabs, hooks, or slots with the mounting bracket.
Reinstall the 2 mounting screws snugly (do not overtighten).
Reconnect the wiring harness firmly until it clicks.
Reassemble the cover/panel
Snap or screw the cover back into place.

Reinstall the ice bucket
Slide the ice bin back in until it seats properly.

Power on and test
Plug the refrigerator back in.
The ice maker may take time to cool down and begin a cycle (several hours).
Press the Test/Reset button on the ice maker (small button on the side or front of the unit) to run a test cycle if available. You should hear the motor and eventually a fill.
Check the control panel on the door — ensure Ice Maker is turned On (not Ice Off).
Monitor for the first batch of ice (can take 6–24 hours depending on temperature and usage).

Received package, cut open. Removed broken handle. Unscrewed broken support. Support slid right out. Took off end piece. Added end pieces to each new support. Slid new support into place. Re-set screw. Re-attached handle. Couldn’t believe it was so easy!