RF263LXTQ3 Whirlpool Range - Instructions

I reoved old drip pans and installed new ones. Very easy, they look great!

Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Simple-pulled range away from wall, unplug from socket. Removed back panel unscrewed thermoses and replace. Put back panel back on plug in, tested temperature setting before sliding range back on place

Fastest, easiest thing I have ever done! I got my orders so fast it was unreal! Hurrah for good old American know-how. I will always recommend these good people!

Remove the old part and install the new part.

Pleaae prepopulate the manufacturer and part i purchased. I fix a lot of appliances so cannot expend the effort to decipher this.

Be well.

Unplug the stove from outlet so no power going to appliance. Had to use wd on screws to help loosen
Little bit of effort to loosen. Took new element from package. Replaced screws just tight donot over tighten. Plug stove into outlet turned on. Did a automatic clean. Oven clean and baked cake later I am back in business and 63 years. ... Read more Was quote 240.00 to from a local repair person. When using wd make sure you wipe any drip from before turning on oven.

I disconnected power cord from house current. Removed back panels (2). I then removed round knob on front of range. I then removed the 2 screws holding the switch in place. After doing that, I gently removed the actual switch itself from back of face panel. I then separated the 2 elements of the switch.

I took new replacement ... Read more switch and reinstalled the 2 parts of switch and placed back into hole in face panel. I reinserted the 2 front screws that holds the switch in place. I put the selection knob back on. However, the knob does not fit tightly. The shaft on the switch itself is to long, but the switch works fine. You do not even know that knob sticks out further than before. I plugged unit back into house current and tested range element to see if it works. It did so with no problem. I then replaced rear panels and secured all screws back to their original location and that was all there was to it.

No problem. Was a fast and effective installation.

First Things first, unplug unit, remove rear cover with Phillips head screwdriver, disconnect, wires from broiler element which is the top, one, open oven, unscrew top screws first, then two at the back, wiggle out element, then reverse Steps , test repair before putting cover back on. Then ta-da, you saved yourself a $300. Service c ... Read more all to the appliance repair guy.

We cheated; a local appliance repair company was called & the tech guy repaired it in 10 - 20 minutes. Couldn't be happier.

After doing a YouTube search. I successfully completed the repair by easily diagnosing the issue with the element.
I watched a video about 5 most common problems with whirlpool broiler elements.
The first being to inspect the element for damage. I found a small section that appeared to be rough and had a raised bump.
I ... Read more decided to order a new element because the oven is older and it wouldn’t hurt to install a new one even if this wasn’t the issue.
Once the part arrived, which it did quickly, I followed the video instructions. It was easy and straight forward. I completed the task in under thirty minutes. It was very simple and I now have a functional broiler element.

The repair was easy. I unplugged the stove, removed back panel, pulled knob and removed 2 screws to remove switch. Unplugged old switch, plugged in new one and installed the 2 screws for switch. Had to snap off stem for new switch to fit knob (easily done with pliers with provided notch). Put knob and back panel back on. Total time, maybe ... Read more 20 minutes.

I had to unscrew the handle from the door as well as take out the front glass, put the trim in place (Thank God for the bottom placement nipples on each trimpiece), hold everything together after aligning all the pieces in place while I screwed the handle back on. The reason I was replacing the trim in the first place was that it is fragi ... Read more le plastic that had broken on both sides when I replaced one inner glass piece that had broken.

This is a cook stove that is used 5 months a year. We have not fixed it yet because we are now in Florida the stove is in New York. We ordered that part just before we left NY for FL so the repair will be done in June of 2021.
George Clark

Replaced switch. Works right now.