This French door hinge is an authentic OEM part used in refrigerators. It is used to provide support and stability to the door allowing it to open and close smoothly. The hinge is vulnerable to wear and tear, and mechanical damage over time. A faulty door hinge will result in difficulty opening/closing the door, door misalignment, inadequ...Read moreate sealing, and increased energy consumption. To begin this repair, locate the screws that hold the hinge to the refrigerator frame and remove them. Carefully lift the door off the hinge and set it aside. Remove the faulty hinge and position the new one in its place. Reattach the door to the new hinge and secure the hinge to the refrigerator frame using the appropriate fasteners.
The ice maker cube tray holds the water that comes from the ice maker during the process of it becoming ice. This part is white in color and made of plastic. All you will need for this repair is a flat blade screwdriver. Over time, the tray may bend out of shape or mineral deposits build up inside, which makes the ice stick to the tray. Y...Read moreou will find the ice maker underneath the ice bin in the freezer. Use your flat-head screwdriver to release the tab holding the ice maker in place, this will expose the ice tray.
This is a door gasket, also known as a door seal, for Samsung refrigerators. This door gasket is used to create a barrier between the cooled interior temperature of the refrigerator, and the warmer temperature of your home. If this door gasket is warped or damaged in any way, you need to replace it immediately so your fridge can continue ...Read moreto cool optimally. To replace this gasket on your fridge, you simply need to pull off the old gasket, and carefully wrap this new one around the perimeter of the door. This gasket is sold individually and does not come with any other parts or accessories.
This is a 40W/120V ice maker assembly for your refrigerator. Ice maker assemblies are designed to continuously make ice cubes by supplying water through its valve, freezing it, and then ejecting the cubs into the ice bin. This ice maker assembly is made of plastic and measures approximately 12 inches, long by 4.75 inches tall and 4.5 inch...Read morees wide. This ice maker is an OEM part that does not come with any other installation parts and attaches within the freezer compartment via its single wire harness.
This is an evaporator fan motor for a wide range of Samsung refrigerators. Evaporator fans pull warm air through evaporator coils to cool and maintain the internal temperature of the refrigerator. If the evaporator fan motor in your refrigerator is not working properly, your fridge will not cool properly and may even prevent the ice maker...Read more and water dispenser from working, and it will ultimately need to be replaced. This OEM evaporator fan motor measures approximately 4 inches long by 4 inches wide and will need a screwdriver and needle nose pliers to be removed and installed.
This sensor cover, also known as the ice maker thermostat cover, is a genuine OEM replacement part for Samsung refrigerators. It is made of durable white plastic and has measurements of approximately 2.25 inches by 1 inch. The sensor cover is responsible for protecting the ice maker thermostat from contaminants, ice build-up, water, and m...Read moreoisture which can prevent the thermostat from regulating the ice maker temperature properly. If your ice maker is producing ice very slowly and you also notice large clumps of ice in the ice tub, then the sensor cover is likely damaged, or it has fallen out of place. You will need to remove the freezer drawers to replace this part.
This is a power cord made for Samsung refrigerators. If your current power cord is damaged, broken, or no longer supplying power to your fridge, you can disconnect it from the wall outlet, strip it from your fridge, and replace it with this OEM cord. This power cord is sold individually and does not include any other parts or accessories.
This is a temperature sensor designed for use within Samsung refrigerators. Temperature sensors are used to accurately detect the internal temperature of your fridge and communicate with the control board to adjust the cooling level depending on your settings. If your refrigerator is not cooling properly, whether too much or too little, t...Read morehis sensor may be bad or defective, causing your control board to incorrectly cool your fridge. This temperature sensor is an OEM part that simply attaches with its wire harness to the control board and has a single temperature probe at the opposite end. Replacing this sensor will require a screwdriver to access it. This sensor is sold individually and does not come with any other parts.
This genuine OEM door hinge bushing or grommet is installed inside the door panel of your refrigerator. It creates a smooth surface for the door hinge pin to pivot in, preventing door misalignment and ensuring a tight seal to keep your food fresh and your energy bills low. You will find it within the hinge assembly, usually at the top or ...Read morebottom of the refrigerator door where it connects to the main body of the fridge. If the bushing is broken, you might notice the fridge door is harder to open or close, makes unusual noises during operation, or appears misaligned. Since this replacement part is sold individually, make sure to confirm how many your model will need before making your purchase.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
old gasket mold and torn
4 of 4 peoplefound this instruction helpful.
Derek from MALIBU, CA
Very Easy
Less than 15 mins
Pull out old one from right top. Wipe track with a cloth and some Windex. Wipe with clean cloth place gasket over where it will replace old. Start right top push into track. Time 10 minutes once all seated again go over the entire gasket check all in track push with thumb easy replacement!!
Was this helpful?
Thank you for voting!
The spring broke on the door flopper
8 of 17 peoplefound this instruction helpful.
Stephanie from MANCHESTER, CT
Very Difficult
More than 2 hours
I didn't do the repair because you sent me the wrong part.That was mislabeled. Then you want me to ship it back but didn't pay for the shipping?And that would be twelve dollars so it's going in the trash!! Very displeased
Was this helpful?
Thank you for voting!
icemaker would not stop making ice
4 of 11 peoplefound this instruction helpful.
John from HILLIARD, OH
Very Easy
Less than 15 mins
Screw drivers
removed the front food tray removed the broken ice maker shut off arm from the left side of the ice maker using a short Phillips screw driver, very little room between the ice maker and the side of the fridge. secured the new ice maker shut off arm with the same Phillips head screw, the arm self positions
... Read morevia a locating notch