RER406GD2 Kelvinator Range - Instructions

Anthony J from HAMMONTON, NJ
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowels needed to be replaced

I just took the old ones out and replaced them with the new ones. It took less than 5 minutes.

Parts Used:

Francine from OTEGO, NY
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

2 of 2 people found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Burner element failed

Plugged the new one in and it worked.
I did search out Frigidaire parts and there are other types tha may or may not work. Calrod burners are not all that unusual. I went with the real thing.

Parts Used:

6-Inch Coil Burner Element

Robert from New Castle, PA
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Can't regulate burners

Didn't get repaired because I could not get the right parts to fix it. You would send me a part for the oven. The oven and burner parts are not the same

Parts Used:

Burner Switch Kit

Pam from OCKLAWAHA, FL
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Old drip pans had turned to rusty lace.

Unplugged elements. Removed old pans. Wiped out holes. Inserted new pans, replaced elements.

Parts Used:

Helen from PAWLEYS ISL, SC
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Rusted Drip Bowls

This range is probably 30+ years old. Still works great. Just needed to replace the Drip Bowls.

Parts Used:

Carolyn from OCEAN PARK, WA
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Original terminal degraded and faulty

Turn off power, remove heat coil assembly and drip pan. Unscrew the terminal assembly from the range top. Cut back 3 inches on each terminal wire and strip insulation 3/8 inch. Terminal assembly should be with the short side of the black block (from the side securement hubs) facing toward the coil stems. Slide the shrink wrap onto each wire and Twist each old with each new wire using the wire nuts and slide the shrink wrap Over each. Using a hair dryer, heat gun, or open flame carefully shrink the wrap. Secure the terminal back in place on the range.

Parts Used:

Robert from PRAIRIEVILLE, LA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Drip bowls needed replacing

Removed the old ones and inserted the new ones.

Parts Used:

Doris from SUN CITY, AZ
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

replaced terminal block for element

followed the video provided on line which was very helpful..

Parts Used:

Donna from UNION, OR
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Terminal block was bad.

Cut the old block off tied new wires to hot wires . That easy!

Parts Used:

Chuck from EVANSVILLE, IN
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

oven heating element

I just removed two screws. Pulled the element out, unhooked the wires. plugged the wires into the new element screwed it in and was done

Parts Used:

Simon from New Port Richey, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Oven element burned out

Really easy--unscrew screws, pull element out, unclip wire connection. Re-clip to new burner, put back in--done. Saved a $100 tech trip PLUS double mark up on part!

Parts Used:

Dr. Johanna V. from North Conway, NH
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Wrench set

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

The old element caught fire.

Unscrew the old one and unplug the wire leads. Then plug in the new one and bolt back up.

Parts Used:

Kyle from Jacksonville, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver

1 person found this instruction helpful.

Was this instruction helpful to you?

Thank you for voting!

Lower element wouldn't heat

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, replaced witht he new element

Parts Used: