REP3422AL0 Roper Dryer - Parts

This part is the replacement single front panel clip for your dryer. It is made of metal and is approximately 2 inches long and ¾ inch wide. The front panel retainer clip is what holds the front panel on to the dryer. If the clip is damaged or missing, or if the front panel appears loose, you may need to replace the clip. This part is sold individually and is an authentic OEM part.

This touch-up paint can be used on a wide variety of household appliances. It is most often used on washers, dryer, refrigerators, dishwashers, ranges, freezers, trash compactors, or microwaves. It is an 18 ml, or.6 fluid ounces, bottle of touch-up paint. It also features a brush for easy application. This quick-drying, long-lasting paint...Read more is perfect for fixing any nicks, scratches, or chips on the exterior of your appliance. This paint is white in color, and provides a durable finish.

Replace the shaft of your left side drum support roller with this part from Whirlpool/Kenmore. This replacement shaft is 2-7/8 inches long. It is meant for use with many of Whirlpool/Kenmore's gas and electric clothes dryers that have been manufactured since 1965. Also known as Drum Roller Shaft.

Replace the shaft of your right side drum support roller with this part. This replacement shaft is 3-3/16 inches long, but does not require a washer or a nut.

This part is the replacement motor pulley for your dryer. The motor pulley allows the dryer belt to run straight while the dryer is operating. If your motor pulley is damaged, your dryer may not tumble, and may not start altogether. A damaged motor pulley can also damage the dryer belt, and it may need to be replaced as well. Be sure to d...Read moreisconnect power from the dryer before you begin this repair. This motor pulley is a genuine OEM part sourced directly from the manufacturer.

The leveling leg locking nut is an OEM replacement fastener for use in dryers and washers. It has a head diameter of 3/8 inches and a thread pitch of 16 threads per inch. The nut secures the leveling legs which helps to stabilize and level the appliances when they are placed on uneven surfaces. The nut ensures that the leg is stable and d...Read moreoes not move during operation. Over time, the threads on the nut may become stripped, or the nut can corrode and break rendering it unable to secure the leveling legs. A faulty nut will cause the appliance to shake and vibrate excessively, and potentially damage the floor and its internal components. It is recommended to replace both the leveling leg and nut at the same time. Use a wrench or pliers to loosen and remove the old locking nut from the leveling leg. Thread the new nut on to the leveling leg and ensure that it is tightened securely. Be careful not to overtighten and damage the threads. Gently shake the appliance to ensure that it is stable and level. Each nut is sold individually.

Specifications: Length 79-1/8 inch, width 1/4 inch, 4 ribs, Flat.

Appliance spray paint is a great way to cover up any chips and scratches that have appeared on your appliances. Instead of replacing the part entirely, this is an easy fix. This is also a great way to give a fresh new look to any handles or areas that have discoloring due to wear. Make sure to clean the area before you begin and wear a pr...Read moreotective mask for safety. Give the can a good shake and spray a few inches away from the surface. Apply the paint until the area is fully covered as desired. Wait until the paint has dried before using the appliance.

This screw is sold individually.

This is a door handle for the door of your dryer. It fastens to your appliance in order to allow you an easy way to firmly pull and push the door open and closed. The most common reason for needing to replace this part is if your current one has warped over time and may be broken. This part is just over 5 inches long, and 2.5 inches wide.

This screw is sold individually.

This front bearing and seal kit comes with the adhesive.