RDE2300E Roper Range - Instructions

I removed (2) mounting screws from the back of the oven and pulled the element out far enough to access the terminal lugs. I unplugged the old element and plugged in the new element. I also replaced the old mounting screws w/new hardware and replaced one of the terminal lugs on a damaged wire. I went ahead and replaced the broiler elem ... Read more ent at the same time (also only 2 screws on the top of the oven) although there was no indication of a problem. The process was very easy although I caution non-electrically skilled people to insure the power is off at the breaker panel when performing this work and, if the electrical wires are damaged, seek qualified assistance to repair them.

We turned off the power to the unit, removed the old element and secured the wireswith electrical tape to keep them from going back into the insulation at the back of the stove. We ordered a replacement part. After turning off the power to the stove again, we inserted the element and screwed in the brackets. The element worked GREAT! I ... Read more t saved us having to buy a new stove for the rental unit. Thanks, PartSelect!!

I removed the existing knobs and popped the new ones into their place! It was aggravating that I could not find a local source to purchase replacement knobs, so I was very glad to discover PartSelect. Instead of a $1000 replacement cooktop, I replaced the knobs for less than a tenth the cost.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reconnected the two wires to the new element, pushed them back into place and replaced the screws. Simple. Turned on oven to test.

Dear Part Select:

Thanks! You got me out of the dog house today!

I received the oven part, installed it- it works great! Thanks for your prompt service! If ever I need another part in the future(and I am sure I will) I have you at the top of my list!

First I removed the power to the oven by turning off the ... Read more circuit breaker to the oven. After that, I removed the two screws (one on each side), that held the old bake element (the element on bottom) in place. I then pulled the element out about 3 inches and disconnected the single wire that connects to each end of the element, (2 wires total), then installed the new element in reverse order.
It was a snap!

Sincerely,

Dennis T.
Amarillo, Texas

Before performing any service on an oven, find the breaker switch and turn off power to the appliance. Test to be sure.

The bake element is held in place by a single screw at each end (two total). This being a very old oven, I removed these with an impact to avoid rounding out the heads, but a regular Phillips screwdriver would ... Read more suffice so long as one is careful (do NOT use an impact to put the screws back in).

With the screws removed, gently pull the ends of the old bake element out of the oven wall. The ends where the wires connect are bent 90 degrees, perpendicular to the sides of the bake element, so take care not to hook the connectors on the edge of the wall opening as you pull them out. Don't pull the connectors off of the old element until you have secured the wires to prevent them slipping back inside the wall of the oven, or you may never fish them back out. I used a couple clothes pins.

Inspect your wires and connectors for damage and corrosion. If the insulation on the wires is at all brittle, discolored, missing, or if the spade connectors are discolored or loose, replace these with the parts included with the bake element. A dirty, poor connection will cause resistance, which causes heat, which will fry your new element same as the old one if your wiring is in bad shape. I had to trim about three inches off of each wire and splice in the new wire sections that came with the new element. For this you'll need wire strippers that can handle 10 gauge wire. Trim away any damaged wire, then strip the insulation from about a quarter inch, and splice in the new sections using the provided wire nuts. I followed with electrical tape to ensure these connections weren't stressed when tucked back into the inside of the oven wall.

Once the connectors are ready, simply place them over the connector blades on each end of the new element. Gently tuck the wires back into the oven wall, followed by the ends of the bake element. Push the ends back into the oven wall until the screw holes align, and replace both screws.

With everything reassembled and tools accounted for, turn the power back on and test the new element. It will give off a new appliance smell the first time as it burns off oils from manufacturing and/or storage. This should subside within 15-30 minutes.

The whole process takes 15-30 minutes, probably less if your wiring and connectors are in good condition. Take your time. The main things that can go wrong are mistakes such as losing the wires inside the oven wall, or failing to make sure the wiring and connections are clean and properly insulated. The bake element itself is largely plug-and-play.

We thought we'd try to fix it before we went out and brought a new (special order) stove/oven. The element came right out and the new one fit prefect. We were very happy that you had a part for this old thing and it was very easy to order from your web site. When the top element goes out, we'll be back!

Removal of two phillips head screws, pull 2 wire connectors apart, reversed the procedure and now the temperature I select on the oven controls is within 20 degrees of what the oven actually heats up to!!!

Turned off circuit breaker
unscrewed two screws holding element in place
carefully pulled element from back of oven about 3 inches.
disconnected wires from element
installed element in reverse order

Pulled out old element after unscreding it. I went on your site and found anelement that looked similar. Drilled in holes on end and put it in. Then screwed it in place.

I had only to remove two screws to remove old element.
I then pulled element out approximately 3 inches to disconnect the two wires.
I put clothespins on the two wires to prevent them from sliding back into unit while preparing new element for installation.
Plugged in wires into the element and fed them back into holes at b ... Read more ack of oven.
Put aluminum foil under new bake unit for drips while I was there anyway.
Tested element to make sure it worked okay.
Thats was it.

First cut electrical circuit to oven for safety, then removed screws, two Phillips head, removed two wires from element, and put some clips on those wires so they wouldn't fall behind the oven wall. Then I got the new element, put on the two wires removed from the old element, attached element to rear wall of oven with the two screws rem ... Read more oved previously, closed circuit breaker to oven, tested oven and it worked fine! Just like new. Standard shipment was plenty fast enough.

Very easy. Removed shelves after turning off breaker then removed screws holding element and removed screw holding wire. Removed old element and then placed new one. Attached wires with screw and then placement screws. Turned on break, replaced shelving racks and turned on. It worked and 5-10 minute fix.

Dean was very helpful. He looked through the numerous model numbers and found just the correct knob even though the model number was no longer in use. I'll be calling back with another repair problem soon. Thank you very much.

Turned off circuit breaker. Removed two mounting screws and pulled element toward front of oven to reveal one wire on each side clipped to element. Removed clips from old, then reconnected to new element. Pushed back in place and reinstalled two screws. Turned circuit breaker back on and ops checked. Very straight forward repair.