RCBS536WJ2WW General Electric Range - Instructions

First I slid the stove out and unpluged it, then removed two screws,slid out element, disconected two wires, slid new element in to place, pluged two wires in ,put into place and installed two screws, pluged stove back in, and turned on to try. Works perfect.

1)Turn off power to stove
2)remove 2 bolts holding heating element
3)pull element out of the back of the oven about 8" so that the wire connects is visable
4)pull wire clips off of heating element and remove element from the oven
5)put wire clips on the new heating element
6)push new heating element back into the ... Read more holes in the back of the oven
7)screw botls back into the oven holding the heating element in place
8)Turn power back on

The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U ... Read more nscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient

Removed screws using nut driver. Pulled element way forward until wires came through. Pondered how to detach burned out element from wires. Chickened out, call neighbor who grasped things firmly with two hands and pulled. Old element came loose. Popped in new element. Cursed the screws that wouldn't align with holes to support element; fi ... Read more nally did it. Screwed element plate in place. Put oven door back on, plugged it in and turned it on hoping that we hadn't reversed the wires. Job accomplished.

My husband did it, we unplugged the stove first then he removed the damaged element replaced it with the new plugged it back in and we were in buisness. I like that this was an acutual part for my stove(not some universal thing) and it arrived very quickly.

my husband who is very handy took it a part, replaced the glass and put it back together - he did remove the door from the oven first and put it on the counter to work on it.
I had the schematic picture of the door ready in case he needed it. He didn't really.

I was very pleased with how quickly the new oven rack arrived and it was a perfect fit. Thanks.

After turning the power off to the range, it was as simple as removing the screws for the broiler itself and the bracket and plugging in the new element. Yes, it was that easy.

I spent more time turning off the breaker and opening the door than replacing the element.

Nut driver to remove the 2 screws, NN Pliers to remove the leads, remove the element and reverse the process.

Hope this isn't copyrighted..... so easy, a caveman could do it!

The hinge mechanism in the back of the range top, could not be fitted to the new part. I needed to enlarge a couple of seat holes on the underside in the front portion of the new part to make it seat securely enough so the hinge mechanism could be safely deleted. (The new top is now simply sitting on the range, without hinge in the back) ... Read more .
More care should have been used to identify the correct top for the exact model and serial number of the range. Even though I had communicated those numbers when I ordered the part, and the picture looked like the correct part, the problem arose.

The broiler uses two male slip-on connectors that attach to two wires with female connectors in the stove. When removing the broiler element, I discovered that one of the two wires was burned in half specifically where the wire crimped to the female connector. This is abnormal and raised some concern. However, I deduced that the terminal ... Read more crimp from the factory must have been defective and the wire nicked or cut in order to produce enough heat at that point for the wire to burn and fail. The female crimp terminal is a special, solid right angle design that I was unable to locate locally even at an electrical wholesale distributor. A straight terminal connector was used and crimped after stripping a new section of the wire. Heat will melt solder. You must use a high quality crimp connector and tool. The connector was then very carefully angled down slightly to maintain a safe distance from the back shield of the stove to the wire when in place. The new broiler works fine. There was likely nothing wrong with the old one. Just a wiring issue.

Followed the instructions online, very simple, quick and painless.

Thanksgiving was coming and I needed extra oven space. So I ordered an additional rack. Installation ... just put it in the oven. My part came the day after I ordered it.

First I unpluged the unit from the recepticle, then unscrewed the back panal from the oven. I removed the to wire connections from the bake element and then removed the two screws from the element itself. I removed the element and did exactly the sae in reverse to install the new unit.

I was surprised to find that the 2 screws holding on the plastic end caps were not philips. it looked like an allen wrench deal but that didn't work. Turned out that I had to buy a hex tool. Looked kinda like a swiss army knife but had allen wrench like hex tools in various sizes. By then I was determined to finish the job even if it mean ... Read more t buying a tool I'd never use again. The job took about five minutes once I had the right tool. The stove looks normal now. The stove looks brand new but for some reason there were cracks in the end caps where the screw hole were.