RB800CJ3CC Hotpoint Range - Instructions

I removed the rear lower cover. Disconnected the terminals from the heating element. Removed 2 screws from the heating element from inside the oven. Removed the heating element. Reinstalled everything in reverse order.

One wire at at time then used my razor blade to get front off stuck right back on

I used pliers to remove the hex bolts from the old burner element and pulled out the terminals by hand. I ordered my part and was slightly concerned because the part number was different (this due to my oven being so old I guess). After reading another repair story on this site, when I got my new part, I turned off the electricity to th ... Read more e range at the fuse box vs. unplugging the oven from the wall - because if I had pulled out the oven to access the plug, I would have had to re-caulk along the edges where it connects with my counter tops. I then slid the terminals into the female parts; this was a bit tricky because the female parts had receded behind the insulation in the hole in the back of the oven where they are located. I used small needle-nosed pliers to grab them and pull them forward enough to slide the new terminals in (by hand). I then put in the old hex bolts and used the pliers to tighten them. Flipped the fuse box switch and tried it out - worked great!

Slide the rang out to access the 240V plug & unplugging it. Removed the sheetmetal cover from the rear of the range to access the slip on wire plugs to prevent damaging the insulation. The insulation would be damaged if pulling them through the opening in the oven wall with the plugs attached to the element. Removed the racks from the o ... Read more ven. Unscrewed the retaining screws holding the element to the rear wall of the oven, lifted damaged element out and reversed the process for instillation. Perfect opportunity to clean underneath and behind the range.

THE INSTRUCTIONS THAT COME IN THE EMAIL ARE VERY GOOD. BE SURE TO TAKE A PICTURE OF THE WIRING.

Did the repair just like the video shows.

Used nut driver and removed the 4 nuts holding the broiler. Pulled electrical wires of old broiler Received new unit and it was just as easy to replace. Thank you for assistance.

PULL RANGE OUT FROM WALL & ALSO REMOVED OVEN DOOR BY SLIDING UP. WORKING FROM INSIDE OVEN & ALSO BEHIND I REPLACED PART . ALWAYS " UNPLUG " RANGE BEFORE YOU START.

I began by turning off the breaker in the panel.
Slide the oven out into the open area.
Removed 3 screws in order to remove rear top panel.
Took 2 pictures of the wiring location on the PCB
Removed all wiring going to the circuit board total of 8.
Removed 4 screws in order to remove bad PCB.
Remove faceplate ... Read more from bad PCB (you will need to place this faceplate on the new PCB.

To Install.
Reverse steps above

Pull out wires & replace element by putting wires back in then tighten...done!!!!

This was simple enough to repair for me, a relative novice. Just remember you need a nut driver to take the back panel off, take a photo of the existing board so you remember which wires go where, and you definitely need a hair dryer to heat up the sticker on the old board so you can remove it and put it on the new board.

Disconnect stove electrical connection. Removed 2 bolts common to the upper stove top cover. Disconnected 4 wires from burner element along with 2 retaining clips.
Removed burner element and replaced with new element. Reinstalled 4 wires and 2 retaining clips. Lowered stove top cover and reinstalled 2 bolts. Connect stove electrical ... Read more to wall outlet. Turn on burner element and verify that it works.

Easy

First I found the model number, but it's parts were under a different number. So I ordered what I thought was the right oven element, but it wasnt right . My husband couldnt get it to fit . Well he finaly found the right part number so we could order the right part. We returned the wrong part and got the right element. It went in per ... Read more fectly and the oven is working just fine now. Remember to always look up the part number you need and then order it.

The part that was ordered based on the shamanic wasn't the part that was needed for the repair. It was to short. I took the other screw for the other side and that screw was an inch longer than the screw that was ordered thru your company. I then went too a jar that I placed extra screws, nuts and bolts which l keep in my garage . I found ... Read more a same length screw but a different head and it works perfectly fine. When I ordered the part from your company most of the parts did not have a photo of the part on file, or a description like how long the part is. I still ordered it because it should fit the make and model number that was posted on the shamanic that was showed to me on line.