RB739G3K3 Hotpoint Range - Instructions

Downdraft stove is over 20 years old, but everything else works fine and it would be a real pain to replace it.

This quick-heat back burner is part of a two burner plug- in unit which takes up half of the top of the stove.

I removed the top from the rest of the unit easily removing five screws. Because of the age an ... Read more d long use it was tough getting the old nut off which holds on the disc, but with the help of some spray lubricant it came off. The old wire ends were also rusted, and to get them off I bent up the old holder, which was going to be discarded anyhow. It was a simple matter to plug in the new unit, tighten the nut, clean up the lubricant with a paper towel, and reassemble the unit, which I cleaned inside since it was dusty. After plugging in the unit I turned on the burner...it works like new and has saved me a very costly replacement. I like it so much that even though the front element works perfectly I am considering buying that disc too just so they will match. Finding your company was absolutely great, and I would recommend you to anyone looking for parts. I still have the manual for this stove so I would feel confident in replacing pretty much any part needed....not bad for a 72 year old woman, (My Dad taught me to do my own work and I am a passable carpenter and plumber; a little more wary when it's something electrical !

Unplugged the appliance for safety. Removed two 1/4" screws that held the assembly in place. Carefully removed the wire guard that retains the glass shield. Unscrewed old light bulb and replaced with new part. Reversed the steps after cleaning glass cover.

After TRYING for 2 years to locate a bake element for this Range that has no model number we called your company and with the element measurements and you were able to cross reference and find us the right part. BONUS! We have an oven once again.

The element was easy to install, it did however take some bending to get it to l ... Read more ay flat.

You have a customer for life, I'll NEVER lose this website address.

I had to call for a appointment for repair with GE Appliance because I thought then it . .was something electrical. The technician came out & checked everything out, turned out it was not electrical, The technician went out to his truck got a light bulb from his truck, put it in & it worked. It cost me $121.00 for trip charge from GE appl ... Read more iance for a light bulb that worked, your light bulbs were defective twice. Very disappointed with your products, cost me alot of money for a good light bulb thru GE appliance

Replace part an wires

This burner element is the large element of a 2 element modual.
After removing the modual, there was 6 small metal screws to open the modual to expose the burner elements. After the burner element were exposed there are 2 wires that had to be disconected with a screw driver. Once the wires are disconnecter the burner element is easy ... Read more removed by sliding the old element out and sliding the new element in. Just reconect the wires to the new element and put the cover back on with the 6 metal screws. It took about 30 minutes to complete the task, taking time to clean all the insides to bring it back to new condition. Very very easy job.

very simple! matter of taking out a couple of screws and replacing them!

Disconnect power to burner module. Dissassemble module with nut driver. Screws connecting feed wires to burner were too corroded to remove. Cut wire close to screws, stripped insulation and inserted new ends into new burner. Reassembled module with nut drivers.

ordered part from this site only took about 10 min to install.

replaced lights in refrigirator and freezer

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 2 ... Read more 20 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Piece of cake- remove two screws, remove old element, install new one.
Shipping was prompt and I was glad to see the part was the genuine GE article. The price was also good- about a 40% savings over the local Appliance Depot!

Easy

I really just want to say how fast Part Select sent my part out...I had no idea it would arrive so quick...Thanks Very much for great customer service...obviously the installation of the bake element is very quick, all you need is a screwdriver, 4 screws, very simple..