RB636403 Hotpoint Range - Instructions

removed the end caps from the stove panel, unscrewed the back, unscrewed the old switch, CAREFULLY noting which wire went to which terminal, removed the wires.
Reversed the process. took a little longer because I felt compelled to do a thorough cleaning while I was there.

Oven unit went well and is working. Tilt burner unit was wrong and did not fit. Needs to be replaced by 8 inch tilt burner with four input.

Repair was easy.
Note: the element leads have a potential across them,
so unplug the unit or you'll have an arc strike.

I liked the selection method at PartsSelect.com.
Finding the replacement part was easy from the pictures.
The prices were reasonable.

The part came next day, which was a surprise ... Read more .
Removal and Installation was 4 screws.
I have become a DIY hero.

Only downside was going out for dinner every night ended.
This site is now a Favorite.

I followed the easy instructions and everything went well. I had the new switch installed in about 30 minutes. My wires were different colors than on the instructions but it was still easy to figure out where the wires went on the new switch. Just do not be in a hurry and make sure you measure before you break off the extension bar. My kn ... Read more ob fit on the new switch without any of the parts that came with the switch.

Unplugged oven from mains.

Removed screw holding terminal block to oven top. Used screwdriver to remove clip holding protective card to terminal block. Removed Philips screws holding wires onto terminal block.

Replacing the terminal block was just doing the above instructions in reverse. The only thing different wa ... Read more s to put the speed clip on the range top before attaching the block to the range top.

The delivery of the part was within 3 days.I only had to connect the two screws had biscuits that night.

It was realatively simple, turned off the power to the oven, removed the bake element , by loosening the two metal screws in the back of the oven, with a nut driver and removing the screws, then pulling the element outward, to expose the two wires ,that were connected to the element, using a nut driver to remove the two screws and a pai ... Read more r of pliers to hold the wire connectors, then removed the old element. Installed the new bake element, by connecting the two wires to the element, with the two screws, then pushing the element back in place , attaching the element to the back of the oven, with the two metal screws, finished with the installation, turned power back to the oven , and tested to make sure the oven worked , all done.

popped the new one on!

I ordered the bake element on Monday and received it on Wednesday. Great delivery.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...
Then I installed the new element using the steps above in reverse. Very clean and simple. One tip t ... Read more hough...open your oven door slightly to the detent and pull straight up. The door slips off easily and allows easy access to the bake element screws.

First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. I reattached them to the new element screwed it back in place and I was done. Could not have been easier! Getting the right replacement part the next day after placing the order was a pleasant surpri ... Read more se. This is the second time I used your company and I am very impressed with your service. I recommend you to everyone I can. Great Job!

Removed 2 mounting screws - Removed 2 screws used to attach wiring to element. Received new element and re-attached the 4 screws.

First I removed the two screws that hold the element in place. I then pulled the element out about 2 inches and disconnected the two wires.

I reconnected the two wires to the new element and screwed the new element to the wall of the oven where the element was held in place.

Removed old terminal block by removing one mounting screw. Removed two wires from block. Installed new terminal block by reversing procedure.

Turn off the breaker. Unscrew the element. Remove and replace with new element. Screw it back into place. Turn on the breaker.

That simple, that easy.

First removed screws then removed burned out element.Replaced with new element and replaced screws and cooked pizza.