RB536GW4 Hotpoint Range - Instructions

I looked for a new terminal locally, but no one had s terminal that would fit a 40-year old range. I went on line to PartSelect and could not find my model range, so I looked through all the terminals listed on the website (about 500) but found only one that was close to mine. Mounting holes did not match, but it had 3 connectors with 2 ... Read more 20 capability, so I ordered it. I requested express shipping by UPS and thought I paid for the extra charge. When I got notification of shipment. I saw it was via ground. It went from Louisville to Jacksonville to Clearwater, FL. I ordered it on Thursday night and received it the following Tuesday night. Meanwhile, we had no stove to cook on. When the part came, it took two days to get the contractor back to our condo. He drilled new holes on the mounting box and jerry-rigged the wiring to make it fit. The range is now working, but I was disappointed in the delay in shipping which I agreed to express shipping.

Pulled range out from the wall. Unplugged cord from outlet. Removed old knob, removed two phillips screws a very top of chrome trim, removed six nut-head screws from back to reveal the switches...removed two set screws from the front at knob base. Visually checked to make sure wiring post of new switch matched the old one. There was enoug ... Read more h slack in the wiring to remove one wire at a time and connect it to the new switch in its appropriate place. Put new switch in the panel and secured with the two set screws. Select the bushing that would take up the slack for the old knob to fit on the new switch stem. Held new stem at its base with pliers and used another pair of pliers to snap the stem at appropriate length. (The new stem could not be broken off short enough to have the knob as flush to the panel as the other knobs...this was the only negative factor in the repair) Replaced nut-head screws and phillips screws. I was especially pleased with the quick delivery of the part...even without special shipping rates I received the part in less than 18 hours from the time I ordered it online!

First I unpluged the appliance. Then I removed the cover from the back of the range. I then disconnected the two wires from the element. I then removed the two screws that hold the element in place. I then removed the old element and reversed the process to install the new one.

unpluged unit then removed back panel unpluged element then took the two screws out took old element out replaced with new one put screws back plug element back in put back panel on pluged it in and started baking home made chocolate chip cookies

remove broken heating element and install the new one

The very first thing we did was turned the circuit breaker off and unplugged the range.
My husband removed the back panel and unplugged the switch. Drew a diaghram of the color coded wires. When we received the new one he broke the extension bar off to fit the knob, plugged it in and we were back in business. It was very easy for m ... Read more y husband as he is a mechanic (millwright). However, if you are mechanically inclined it is an easy fix.

I removed the two screws that hold the element in place. I pulled the element out about three inches and
disconnected the two wires. The screw holes in the new element would not accommodate the old screw size so I enlarged the holes to fit. Connected two wires and replaced two screws that hold element in place. End of story.

First, we ordered the part on Sunday afternoon online. It was here by Tuesday morning. We unplugged the oven and removed the screws holding the element in place and the electrical contacts. That was the toughest part because it's hard to get in the oven and they were baked on pretty well. We had to drill holes in the bake element. Be ... Read more careful not to drill them too big, so the screw will fit snug and make contact. We screwed the bake element to the contacts, then back to the over, plugged it in and turned it on. The temperature is more constant and steady than ever, and the oven heats much faster. We were impressed and happy to avoid replacing the whole stove.

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
... Read more />3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Flipped off the breaker for the stove. There were two screws holding the old element in place. Removed those, pulled the element out a little to expose two wires, disconnected those, swapped in the new element, reconnected the wires, and screwed it back into place. Flipped the breaker back on and voila! Barely more difficult than changing ... Read more a lightbulb.

This was extremely easy! I unscrewed two screws, pulled out the old element, inserted the new element and screwed the screws back in. Also, this part came very quickly through the mail. If needed, I will definitely use this site for repairs again.

just put in the new part

unplugged the element took the old pan out and put the new one in, plugged the element back in.

Unplugged oven. Pulled out from wall and removed backside access panel. Unplugged 2 stake-on connectors connected to element. From front side of oven, removed fan guard using 1/4 inch nutdriver. Gained access to and removed two screws holding in element. Pulled element out. For installation, reverse process.

I unpluged stove then opened slightly oven door and lifted it off to get closer. Then with a light to help I took out two screws and pulled the element out. I didn't need pliers to get the wires that are put on with slide on clips. you may need a pair. put wires on slide in place put screws back ,replace door, plug it in and test. Very ea ... Read more sy.