RB525GV5 Hotpoint Range - Instructions

I lifted out the burners and took out the old drip pans ans then replaced the burners. However the 8 inch pans were bigger than the old ones and they do not fit properly. They are sitting on top of the stove and not inserted like they should be. I will have to look elsewhere to find ones that fit.

Removed the burner coil.
Unscrewed the terminal block.
Pulled out the stove and disconnected the 220 Volt service at the plug.
Removed the back panel at the control knobs.
Detached the wiring to the control knob and pulled thru the back panel.
Wiring mostly visable to the front 8 inch burner.
Replaced wiring and mounted new terminal block.
Tested the burner for a few seconds.
Replaced back panel and set stove in place.
Saved $150 dollar service call.

This appeared to be an easy fix, but turned out to be more involved than I planned. The hard part was pulling the range/microwave oven assembly away from the wall so I could remove the back panel and see how the new terminal block wires connected up to the switch/knob that operates the burner. Extracting the whole range unit required me to use a floor jack to raise the leveling feet of the range above the edge of my floor tile so I could slide the unit out. Once away from the wall, I used a nut driver to remove the back panels. Next surprise was the new terminal block wire connectors were not the same type as the old block's connectors (flat vs. male pin-type). Rather than let the scope of this job creep to include a whole new connector rig, I opted to splice the new terminal block wires onto the existing wires that led up to the control knob. I used professional splices and a crimping tool to secure the wires. After checking the new installation was sound and operational, I slid the whole range back into place. Attaching the new terminal block to the range top was a piece of cake, but getting the damn oven out into open space where I could work on it was bear. But, hey, I learned a few things, one of which is that when a homeowner decides to retile their kitchen, make sure you run the new tiles all the way under the range and not just up to the front edge of the oven. I can see why this was done - to avoid having to remove the oven during the retiling - but it creates an obstacle for whenever the oven needs to be pulled away from its location. The last tool I imagined I would need for this repair was a car jack. The Parts Select part worked fine.

Replace part an wires

New one a little different ,but it was marked for wiring!
Had to install upside down because wires would not reach right side up!
Had to pull back side of knob out and turn 180 degrees and glue in knob, so knob would be right side up!
Works fine! Now all burners work again!

First shut the power to the stove,then had to slide the stove out so I could get at the back to remove the panel screws.Once you have the back off remove the knob on the front.Under the knob is 2 phillips screws that you need to remove.Next I took the new switch and matched up the wires to the old switch.Reinstall is the reverse.Once the switch is in place you must remove the excess shaft to match the length of the old one.This is done with the use of 2 pliers,you grasp the shaft with both pliers and snap it off where you need it.The kit comes with spacers so you have got to match up the right one so the switch is solid on the shaft.This finishes the project,next turn the power back on and check that all is working ok.Job finished.

When I pulled the old element out only one of the wires was visible, the other wire was still connected and after pulling a few times it came out , but the wire connector wasnt visible and I had to dig around in the small opening to find it (2 hours worth of digging and pulling) I finally got a hold of the wire and pulled it through and was able to connect it to the element, had to bend the metal around the opening to be able to get my finger in there and find the wire, The screws that hold the element in place wernt the same as the original so i just have it pushed up in place but it seems to work ok , took way longer than i thought it would.

I took out the old broiler support bar, but it was being held by one screw. I did install the new bar with one screw, but I need to obtain a second screw. I still have not located a second screw, but it is inplace.

Removed old surface burners and replaced them by plugging in the new surface burners. Now they work GREAT! Parts ordered and received with-in 3 business days. Fed EX delivered parts in good order very quickly. We recommend PartSelect.com

Removed items from drawer, removed drawer, replaced the two slide inserts and the two aligment guide inserts.Works as it should

Unplug coil, remove pan - place new pan, plug in new element and bingo. Took approximately 30 seconds!

I pulled the oven door off the hinges and took the bolts out of the bottom of the over that were holding the strip on. I then pulled the strip off and replaced it with the new on. I replaced the bolts and then replaced the door on the hinges.

I went online to find the part. I also found a how-todo it self installation instructions. So, I thought I would try it. I pulled the stove out and unplugged it. It took me 2 days to try and remove the screws. They wouldn't budge. On the second day, I was about to give up. I tried to loosen the screws again. It finally moved!! So, I kept at it. Took me about 10 mins on the first screw. Then another 10 or 15 minutes on the second one. Once I took the screws off, I didn't know how to remove the wires. I kept picking at them for about 5 minutes, and it was easy then. Removed the old bake element. Then connected the new element wires, put the screws back in (not tight). Plugged it up and tested it. It worked!!!!!! I've never did anything like this before. If the screws wouldn't have been so hard to remove;it would have went a lot better.

took 2 screws out removed old element, put new element in and put the 2 screws back in. All worked great and I baked bread that same day. The service was fantastic, and $40.oo cheaper than the appliance store I checked with.

Removed existing surface element and replaced with new element.

P.S.

Part Select service was excellent.