RAC4244AL0 Whirlpool Washer - Instructions

The top part of the dial pried off with a screwdriver and the replacement part screwed right back in it's place.

First I removed hose from drain, next I loosened the clamp at the drain hose connection at the washer. Removed hose. Have rags/towels as there is some residual water that will spill out of the washer. Reinstall in reverse.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Lost screw on bottom refrigerator door hinge which allowed the door to fall off. Purchased screw from Part Select for the Roper refrigerator. Drawings and parts list for this unit were available on their website. Easy repair.

Unscrew the broken piece of knob by hand, Pry off the black dial on the threaded shaft with a screw driver , screw on the knob by hand. Done.

First, I read the previous repair stories, so I knew what step to do first. So, first I took the hose off of the drain, then I removed it from the washer. And as the previous repair story stated, some water came out and I had a towel ready to catch the water that was in the hose. I threaded the clamp onto the new hose, pushed the new ho ... Read more se onto the washer, used the pliers to open the clamp to better clamp the hose onto the washer. Then, placed the drain hose into the drain pipe and it was done! Thanks for such a great site!

Tipped the washer over to find where the leak was coming from. After finding it was the hose between the tub and drain fitting on the back of the machine I stood the washer back up and removed the access hatch cover on the back of the machine. Two spring clamps held the hose on which I removed with channel lock pliers. Installation was ... Read more a bit more difficult because the clamps like to slip off the pliers. They make special pliers for these type of clamps but I don't have a pair. I was able to easily get one clamp on but after wasting a few minutes with the other one I decided to just use an automotive type worm drive hose clamp for the upper clamp, rather than struggle with the original wire style clamp.

First opened lid up and took ring cover off tub. Then unscrew 4 back screws and lifted top up. I replaced all 4 straps, so this process is repeated 4 times: with rubber gloved hand, lift metal support stick up, remove white plastic safety lock, insert strap and replace safety plastic lock and metal support stick to original position. Then ... Read more , after removing old strap from tup side, replace the new end. After all 4 all done, push back down ring in position over tub, and screw everything back. The hardest part was holding the metal stick up with the gloved hand (as it was oily and slippery), and using one hand to do the rest, Otherwise, a fast and easy job.

Siphon break kit keeps washing machine from continuing to siphon after rinse/cycle -- like emptying a pool with a hose. Fixed the problem of the tub never filling due to siphon draining out water as it's being put in.

Followed instructions other customers provided for hose installation. Haven't installed agitator dogs yet. Need to watch the video on your web site.

Removed the old hoses and screwed on the new hoses.

Removed broken hose and replaced with new hose. My washer will be 21 years old in January.

1. Need mop, bucket to catch leftover water in machine before you remove old hose. 2. Removed old hose by removing clamp. 3. Dried up any remaining water around fixture before attaching new hose. 4. Slide clamp to bottom of hose before attaching to machine. 5. Attached hose and clamp to machine where old hose was removed from. Make sure c ... Read more lamp is secure. (Please note that clamp that came with the new hose was too big. I used the old one. Worked perfectly). 6. Finally run a little water in you washer, then run out to test tightness and there is no leaks.

Pulled washer out from wall removed clamp and old drain hose addnew hose replaced clamp put washer back in plact connected drain to outlet simple operation

After removing wash cover by unscrewing the 4 screws at the back, I disconnected the electric by pulling the plug connector, this makes for more room to get at the snubbers. Remove the ring that held the snubbers in place, replaced the 4 snubbers , replaced the ring, making sure the position is correct over the snubbers, replaced the cove ... Read more r. Very easy job