This genuine GE drawer support is an original replacement part sourced from the manufacturer and is designed for use with electric ranges. Made of durable plastic, it attaches to the rear of the drawer and provides stable support by securing the rear side in place. This part includes the necessary mounting screw for installation and is so...Read moreld individually. It’s a simple yet essential component for maintaining smooth drawer operation and proper alignment.
The function of the oven sensor is to detect the temperature within the oven cavity. If you notice that the oven is too hot or too cold, or it is not heating evenly, you may need to replace the oven sensor. The oven sensor is typically located in the back of the oven so you will most likely need to pull your oven out to access it. Many of...Read more our customers have rated this repair as easy. You will need a Phillips screwdriver to complete this repair. Be sure to disconnect the power source and shut off the gas valve before doing this repair.
This part is sold individually and is for ranges. The control switch turns the surface element on and off and determines the temperature of the element. This will need to be changed if the control switch has failed and the cooktop is not turning on. It is found underneath the glass cooktop. Before beginning, make sure the circuit breaker ...Read moreis off. You will need to remove the cooktop from the counter. To do this you will need to go underneath and see what kind of brackets are holding it in place. The brackets will vary depending on the make and model and type of countertop is it laying on. These brackets will need to be removed.
This replacement haliant surface element is designed for use with flat-top ranges and cooktops, positioned beneath the glass surface to supply consistent heat to the cooking area. Measuring approximately 12 inches in diameter, it provides reliable performance for a variety of cooking tasks. If the burner fails to light when activated, the...Read more surface element may be faulty and require replacement. Installation involves disconnecting power to the appliance, removing the screws securing the cooktop, lifting the glass surface, and replacing the element by disconnecting the wires and securing the new unit in place. This component is sold individually and is compatible with select models of electric ranges and cooktops.
The GE Oven Door Window Pack Assembly is a genuine OEM part that fits select GE ranges and ovens. It includes a heat-resistant inner glass panel, frame, and seals, providing insulation and clear visibility into the oven cavity. Common issues like cracked glass or heat loss can indicate the need for a replacement. Ensure the oven is cool to the touch and wear gloves for safe installation.
This oven door gasket is a high-performance seal made from heat-resistant rubber and fiberglass, designed to create an airtight barrier between the oven door and cavity. Measuring approximately 89.76 inches in length, its flexible construction allows for a precise fit across a range of oven models. The gasket plays a critical role in main...Read moretaining consistent internal temperatures by preventing heat from escaping, which supports even cooking and improved energy efficiency. Installation is beginner-friendly and typically takes under 30 minutes using pliers. Some versions include up to 25 mounting clips for secure attachment. Signs of wear—such as visible cracks, tears, or heat leakage—indicate the need for replacement to restore optimal oven performance.
This part provides a way of connecting individual electrical wires and offers protection of the device from electrical surges (voltages and/or currents).
Ask our experts a question about this model and we'll get back to you as soon as possible!
We may have answered a similar question already! Search questions and answers left by others using simple keywords like "fit", "broken", "easy", or "quality" to find questions that match.
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Sort by:
Prev
1
Next
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
Fred - For model number PS968SP3SS
August 13, 2021
I turn on the broiler, it stays for about and then it turns off by its self, what do you think is wrong? I turn on the bake mode and set the temp and let in a minute it beep to temp I set but the the oven is not that hot. Thank you for any help you can share. Fred
Hello Fred, Thank you for the question. We suggest testing the Oven Sensor. Testing the temperature sensor probe on your oven is easy. With the sensor at room temperature, measure the resistance between the two prongs at the end of the sensor connector. The resistance of the sensor should read approximately 1080 – 1090 ohms at room temperature. We hope this helps!
All of the lettering on the cover plate on each side of the touch pad has worn off. If a stranger used the range they wouldn't know which knob goes with which burner. Can just the stainless piece be replaced or does it have to include the new touch pad?
Hi Bill, thank you for contacting us. We suggest you replace the whole touchpad assembly, part number PS2370122, to fix the issue. Good luck with the repair!
If I purchase the new plate which includes the new touchpad is it difficult to connect the touchpad to the range. Right now all I see is the 4 nuts under the control knobs holding the plate to to the range. I don't want to get in over my head with a complicated electrical problem connecting the new touchpad. Thanks
Hi Bill, thank you for reaching out. According to our research, the glass touch assembly just has a single relay connected to it. To replace the touch assembly, remove the control knobs then screws and detach the relay wire and replace it. There is no complicated electrical wiring under the touch panel. We hope this helps!
1 personfound this instruction helpful.
Was this helpful?
Thank you for voting!
Prev
1
Next
✖
Ask a Question
Ask our experts a question on this model and we'll respond as soon as we can.
See how others fixed this model. Time, tools, difficulty, and steps that lead to victory!View More
Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Oven was not coming up to temperature
57 of 79 peoplefound this instruction helpful.
Sean from Highlands Ranch, CO
Really Easy
15 - 30 mins
Nutdriver, Screw drivers
I had to remove the oven from the wall because the sensor plug connction is behind the unit. Two screws hold the sensor inside the oven and then I disconnected the lead and pulled the sensor out from the front. I installed the new sensor, tightened the two screws holding it in and connected the lead. Then reinstalled the oven into the wal
... Read morel. Overall, a very easy repair once you get the oven out.
Read less
Was this helpful?
Thank you for voting!
terminal block melted
56 of 77 peoplefound this instruction helpful.
jonathan from willow springs, IL
Easy
Less than 15 mins
Nutdriver, Screw drivers
The existing terminal block on my Ge oven/Range had melted due to a loose wire causing sparking and starting the plastic casing of the terminal block on fire and melting it, Part select made the part easy to find and had it at my house in 2 days. All I had to do was remove six screws to take the back sheet metal cover off of the oven. U
... Read morenscrew the terminal connections remove two mounting screws that held the terminal on to the oven body. This was a little trickier than it should have been because the melted plastic had reformed making it very hard to access the mounting screws. i then mounted the new piece and plugged the oven in, it took 15 minutes and was very easy. definitely saved me at-least a $100 for the service call i would have made if finding the part wasn't so convenient
Read less
Was this helpful?
Thank you for voting!
Plastic drawer support snapped off
30 of 35 peoplefound this instruction helpful.
Jeff Troiano from Sayville, NY
Really Easy
Less than 15 mins
Screw drivers
The repair went very easy. The replacement part was designed differently than the original part. It installed on the rear of the drawer with a screw as the original snapped into the side. This was a bit confusing when researching and looking up the part online.
My Orders
