PS950SF2SS General Electric Range - Instructions

had to remove the oven from the wall. once i realized that i had to take the side wall brackets off before removing the oven it was quite easy. then just had to remove oven door and slide the unit onto a chair while replacing the sensor. put it all back in and the wife was so happy to have her oven back she made me a batch of brownies. yu ... Read more m.

This temperature sensor is very easy to replace. There are two screws inside the oven in the top middle of the back of the oven. Take these off. on the back of the stove there is a metal plate with 5 screws I believe. Take these off with a nut driver. Then you will see a white connector coming from the spot where you took the other screws ... Read more off. Take the white connector apart and pull out the temperature sensor from the inside of the oven. Then put the new one in.

Turned off power at circuit breaker. Disconnected electrical connections from stove and lifted stove top out of counter. Removed glass top by removing about 8 screws from side of stove top.Replaced burner element and replaced glass top.

I picked the least expensive and most likely issue with our oven that was not indicating a correct oven temperature. I am sure with a 15+ year appliance that the circuitry is on its way out but wanted to give this a try to avoid a new appliance purchase. Oven pre-heat setting takes much longer to finish with the age of the oven. However, ... Read more after the new sensor the oven will maintain a more even temperature for the cycle.

Removal of the sensor from the inside of the oven is a bit awkward since it is located between the broiler elements at the back but a nut driver was the correct tool and worked fine. A bit stuck with the heating of the connection but pretty simple to replace. Must remove the back first to uncouple the connector. Simplest part of the repair.

At best a temporary fix for a an appliance this old.

Removed the oven door and shelves. Moved the oven out from wall, so that I could access the rear panel. Unplugged the oven. Removed the five (5) screws holding the rear panel in place and removed the panel. Disconnected the sensor at the connector. Removed the screw holding the sensor in place inside the oven and removed the sensor. Thea ... Read more ded the sensor wire through the rear of the oven wall. Installed the sensor and screw to hold it in place. Snapped the connector from the sensor to the mating connector at the rear of the oven. Installed the rear panel. Installed the five (5) screws to hold the panel. Plugged the oven back in and slide the oven back to the wall. Installed the oven shelves and the oven door.

First I removed the 4 screws that hold the element in place. I then pulled the element out about 3 inches. I removed the sensor and disconnected the connector.

The repair was very easy to do. Our oven was showing the F2 error code, which is associated with an over-temperature fault. Upon inspection, the oven was warm, but definitely not beyond the temperature threshold. I researched the issue and found this temperature sensor.
Swapping the sensor was extremely easy. You take off the back pa ... Read more nel of the oven, unhook a single wiring harness, and undo some bolts inside the oven, which allows you to pull off the old sensor. Simply hook up the new sensor to the harness, pull everything back through, replace the fasteners, and you're good to go.

pull out stove, unbolt old temp sensor inside stove with 1/4 nutdriver, go to back of stove and take off cover and unhook sensor and hook up new one, put all back together and slide stove back in place.

The real challenge on this particular glass top range was to figure out which screws had to be removed to lift the glass top to get at the burner elements to do a replacement.

Removed the two side screws holding the control panel in place. Disconnected the two wire harnesses and took off the control panel to allow easier acces ... Read more s. Then examined the screws attaching the vertical plate in front of the glass top. Most of them were on the on the vertical plate but a few were in the bottom of the horizontal plate. If successful, the vertical plate can be moved forward giving access to the glass top. You pull up on the front of the glass top and when it just clears the vertical front plate you pull the top forward a bit to get the back end of the top out of the read chrome vent piece. I then leaned the glass top up to about a 75 deg angle and then propped the top with a 24” wooden garden stake. I used two stakes to hold the top up. The challenge after that is to remove the old burner and carefully note the colored wiring and locations of the connectors and removed the three old clips. That took a bit of effort. several of the wiring harnesses were very short so you had to be careful when removing and installing the new burner. The burner has numbers stamped on the metal and you must note each number where the clips are located. The rest is to reverse the process. Some of the insulation pieces came off and some of the insulation clips fell off and you must be sure to get the insulation pieces back on in the correct location. Expect a lot of gunk that needs to be cleaned on the top and trim pieces. I save around $200 by doing my own replacement.

Very easy to remove the parts and to reassemble

I checked various sites on the net and decided that the temperature sensor was the problem. The GE price for the replacement part was about $105, most of the other sites offered the sensor in the $70 range. PartSelect $12.95 When the part arrived, I removed a small self taping screw, pulled the high temperature wire connector into th ... Read more e oven space, disconnected the quick disconnect fitting, attached the new temperature sensor, pushed the connecting wire into its hole, replaced the screw and that was it. I probably saved about $200 in parts and labor over what a local repairman would have charged. Oh yes!! I first disconnected the power at the breaker box. Very important.

This item worked as described. I paid more for this 'oem' probe than the generic 1 because i didn't want to chance it not working as others have reported.
- works great. tested it....snaps in, reads correctly, snaps out.

Performed repair using a video for reference.

The logical first choice for replacement was the triple burner assembly since that is subject to failure for obvious reasons. It turned out that the burner assembly was fine by visual inspection and by virtue of a continuity measurement.

The second choice seemed to be the frame relay board and that turned out to be correct. T ... Read more his was an educated guess since it is the "next" component going backwards, it is responsible for distributing the burner voltages, and that relays can have a reasonably high failure rate. This board could be tested but without schematics that seemed like a lot of effort, so I ordered it on a best guess.

Replacement of the board is not too difficult but does require some attention to detail, and patience is required to be sure that all the wires end up in the right place. Needle nose pliers are really helpful here. Take photographs, make a sketch, and label some of the obscure wires with painter's tape. Took about an hour or so.

Took the oven door off and removed the inner door panel, put new glass assembly part in and reassembled. The hard part was getting the door hinges locked back into place.