PRTT212 Powermate Tiller - Parts

This forward control cable, compatible with various tiller models, enables forward movement when pulled by the user, engaging the forward gear. Measuring 1440mm (approximately 57 inches) in length, this control cable is equipped with a protective sheath to guard against external damage. It is an OEM part and is sold independently, without...Read more any additional securing hardware or parts. If your tiller control cable displays extensive wear, fraying, corrosion, or fails to engage the tiller correctly, it is essential to replace it promptly for optimal tiller functionality. To replace the control cable, you will need a wrench and/or screwdriver. Begin by turning off the tiller and locating the control cable near the handle. Disengage it by unscrewing and disconnecting it from the handle. Follow the cable to the engine transmission, typically held on a clip, and disconnect it. Install the new cable to the tiller handle and the engine transmission, ensuring it engages the transmission when pulled from the handle, and then test for functionality.

This extension control cable is designed to restore reverse functionality in outdoor power equipment such as tillers and mowers. Measuring 1430mm in length, it serves as a direct replacement for malfunctioning or worn cables, ensuring reliable performance and smooth operation. Manufactured to OEM specifications, it offers compatibility wi...Read moreth select Powermate and Southland models. The cable is engineered for durability and ease of installation, helping maintain the equipment’s operational integrity and responsiveness during use.

This is a genuine OEM supplied replacement wheel that is specially manufactured for use on Powermate and Southland rear tine tillers. It is the right wheel that keeps the unit mobile for easy transportation. This high-quality wheel is sold individually, it consists of a metal rim and a durable rubber tire. Please note the left wheel and the hardware to secure these parts are all sold separately.

This wheel is a genuine OEM part for various models of tillers but is only for the left side of the tiller. Used for moving the tiller around, this wheel measures 13-inches high, 5-inches wide and the rim is 6-inches and made of high-quality metal surrounded by the rubber tire. To replace this wheel, remove the securing hardware on the ou...Read moretside of the rim, slide off the old wheel, and replace the wheel and the hardware. This wheel is sold as an individual part and does not include the necessary hardware to secure it.

This forward drive belt is a genuine replacement component designed to restore smooth and reliable operation to compatible tillers. Known as a 7PK597 multi-rib poly V belt, it connects the engine to the drive system, enabling forward motion and traction. Made from durable rubber, it resists wear and slippage, ensuring consistent performan...Read morece in demanding outdoor conditions. If your tiller is experiencing reduced traction, slipping, or a non-functioning drive system, replacing the belt may resolve these issues. Installation involves accessing the drive assembly and securing the new belt in place. This part is compatible with select Powermate and Southland tiller models—verify fit before installation.

A reverse drive belt is used within outdoor power equipment within the transmission to enable the reverse gear functionality and allow the user to move the equipment backward. This reverse drive belt is a 5Pk740 belt, meaning it is a multi-ribbed V-profile and measures 740mm in length/circumference. This belt is made of high-quality mater...Read moreials and connects directly to the reverse tensioner pulley in various models of tillers and is sold as an individual part. Over time and due to heat, friction, and stretching, this belt can eventually wear down. If you notice poor performance from your tiller when reversing or hear squealing and other unusual noises, inspect both drive belts for any signs of visible damage. To replace this drive belt, make sure the engine is cool and disengage the spark plug cap. Use a wrench to remove the belt guards on top and below the belt, if necessary. Then, using 2 wrenches, disconnect and remove the securing idler bolt and any washers, after which you can remove the belt through the bottom of the unit. Check to make sure the forward drive belt is in good condition before you install the new reverse drive belt. Pull the reverse drive belt up through the bottom of the unit and install it to the appropriate pulleys and tension wheel, followed by any washers and the securing bolt which you will need to tighten. Then simply replace the belt guards if applicable.

This genuine OEM fuel line fitting or filter in your lawn equipment ensures clean fuel flow from the tank to the engine in your lawn equipment. It effectively removes debris and impurities, safeguarding the engine from potential damage. Typically located along the fuel line, it is close to the fuel tank or engine. You can tell if it is br...Read moreoken or clogged if there are signs of fuel leakage, reduced fuel flow, or if the engine fails to start or run smoothly. If the fuel line fitting or filter is not replaced, it can lead to poor engine performance, fuel starvation, and potential damage to the engine components. To remove it, you will need a screwdriver, pliers, and a socket set. Disconnect the fuel hose from the carburetor, drain the tank, and unbolt the fuel tank. Then, detach the fuel line and use a socket to remove the fitting. Remember, this replacement part is sold separately from the rest of the fuel line assembly.

This authentic OEM air cleaner element, also known as an air filter, includes one paper filter surrounded by a foam pre-cleaner for use in a variety of outdoor power equipment. The foam pre-cleaner acts as the first protective barrier and traps larger particles to prevent them from clogging or tearing the paper filter. However, it is norm...Read moreal for the air filter to become clogged or torn due over time, due to accumulated dirt and debris, or due to prolonged use without replacement. A faulty air cleaner will result in poor engine performance, rough idling, hard starting, stalling, and increased fuel consumption. It is recommended to replace your air filter every 3-6 months for optimal performance. You can find the air cleaner housing near the carburetor or air intake on your equipment. Detach the housing cover and remove the faulty filter. Clean the housing and place the new air cleaner in position. Reattach the air cleaner cover to complete your repair.

This fuel tank cap is an authentic OEM replacement part sourced directly from manufacturers such as Powermate, Homelite, Southland, and Airstream. It is made for use with multiple models of lawn edgers. This fuel tank cap is made of plastic and sold individually. This cap prevents outside contaminants from entering the tank. It should be ...Read morereplaced if it is damaged or will no longer tighten. NOTE: This cap only fits the older version of the tank, part number A100783. It dose NOT fit the newer tank, part number A202711. Part number A202712 fuel cap will fit this newer tank.

This manufacturer-approved on/off switch is a control mechanism that allows users to easily turn their outdoor power equipment on and off as needed. It can be found near the control panel or handlebars, within easy reach of the operator. The switch is connected to the ignition coil, and it works by either completing or breaking the circui...Read moret between the spark plug and the ignition coil, to either start or stop the engine. If the switch wires are faulty or the switch is damaged, the equipment will either run continuously or fail to start altogether. To remove and replace the off/on switch, first ensure that the equipment is switched off. Disconnect the wires from the faulty switch and pull the switch off the mounting post. Take the new off/on switch and reconnect the corresponding wires. Secure the switch in place by reattaching the appropriate fasteners.

This is an original Powermate replacement part. The lock pin is designed by the manufacturer for use in rear tine tillers. This part is made of metal, and is generally used in securing components on a shaft. You may require pliers when replacing this item. This part is sold individually.