PP285 Poulan Chainsaw - Parts

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

This is an authentic OEM replacement kit for use with lawn and garden equipment. Each kit includes the carburetor, cylinder, crankcase, and muffler gaskets. The carburetor gasket seals the area between the carburetor and engine block to prevent the entry of contaminants into the carburetor. The crankcase gasket prevents oil from leaking o...Read moreut of the crankcase. The cylinder and muffler gaskets prevent the combustion and exhaust gases from escaping. If you are experiencing common problems such as leaking, loss of compression, and poor engine performance this indicates that your gaskets may be worn down or damaged and need replacement. Carefully remove the old gaskets and thoroughly clean the mating surfaces where the new gaskets will be installed to ensure a good seal. Install the new gaskets and ensure that they fit properly.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The oil cap connects to the saw\\\'s chassis by covering the oil fill spout to prevent spills and to prevent contaminants from entering the oil tank. This item is available as an individual replacement part. Tools are not necessary to install this item.

This is an original part from Craftsman for edgers and chainsaws. This part helps turn the flying wheel when you pull on the starter rope. You may need a wrench set to replace this part. It is recommended to review your models diagram to verify the parts compatibility. This part is made of durable plastic and sold individually.

This is an authentic item sourced from original manufacturer. If the chainsaw bar doesn't adjust when you turn the tension screw usually the tension gear/pin or the adjustment bolt is worn or damaged. This part is made out of metal and it is sold individually. You would need a phillips head screwdriver to remove or secure this screw.

This check valve, also known as a one-way valve, is a genuine OEM part that regulates the flow of fuel/oil in the equipment engine to prevent it from flowing backwards. It is made of plastic and designed for use in a variety of lawn and garden power equipment. If the valve is jammed, worn down, or contaminated with dirt and debris, it wil...Read morel be unable to open and close properly, thus restricting the flow of fuel and compromising the engine combustion process. You will likely notice fuel leaks around the carburetor, engine stalling, hard starting, and overall lower performance from your equipment. To remove the faulty valve, carefully disconnect any hoses or fasteners connected to it. Place the new valve in position and secure it appropriately.

This is an authentic Craftsman replacement part that has been sourced from the original manufacturer to be used with chainsaws. The drum and sprocket are used to house the clutch and to drive the chain when the clutch expands within the drum. The drum/sprocket are one piece and it is sold individually.

This is an authentic part that is specially manufactured for use with Craftsman handheld lawn and garden equipment. The starter grip attaches to the rope to provide a user with a comfortable grip to pull start the engine. Check the owners manual and the appropriate diagram of your model for the correct application of this part. This high-quality component is made of durable plastic and is sold individually.

This bar adjusting pin hooks onto the crankcase along with the bar adjust retainer and the screw. When you tighten the screw it helps to place tension on the bar. This high-quality pin is made out of metal and is sold individually. It is an authentic OEM sourced item which is specially produced for use with Poulan chainsaws. A screwdriver and a socket set may be needed when replacing this part.

Genuine Poulan replacement part, not an aftermarket imitation. This high quality chain is specially designed for use with 20" bars on chainsaws. Over time chains tend to stretch, get dull or break requiring replacement. Keeping an eye on the condition of the chain and its performance will let you know when it is time to replace it. Please...Read more note, this chain is sold individually. The to complete this repair you will need a flat head screwdriver or a socket wrench. • Remove the side panel • Release the chain tension • Remove the old chain • Thread the new chain onto the saw • Reattach the side panel • Tension the chain in accordance with the owners manual

This authentic manufacturer-sourced component is specially designed for Poulan and Husqvarna gas-powered chainsaws. It is an identical replacement for a missing or a damaged retainer that is utilized to secure the piston pin. To ensure the exact location and the correct application of this product, refer to the appropriate diagrams for yo...Read moreur specific model. Keep in mind this high-quality hardware is made of durable metal and is sold as an individual item.