PP258TP (Type 1) Poulan Pole Saw - Parts

This 25-inch fuel line carries fuel from the tank to the carburetor, ensuring proper engine operation. Made from durable clear plastic, it is designed to withstand regular use but may become clogged or brittle over time. Replacing a worn or damaged line can help prevent leaks and restore reliable starting and performance.

This Genuine OEM fuel filter is designed to maintain the performance and longevity of your equipment by preventing dirt and debris from entering the carburetor. Located inside the fuel tank, this essential component ensures clean fuel delivery, protecting the engine from potential damage caused by contaminants. Sold individually, the filt...Read moreer is built to meet original equipment standards for fit and function. Over time, the filter may become clogged, restricting fuel flow and making engine starts more difficult. For optimal performance, it should be replaced—not cleaned—at the first sign of blockage or wear.

This is the Genuine Craftsman replacement part. It is made out of Flexible Rubber and is Sold Individually. The purpose of the 530069216 Tank Purge Line is to return the excess fuel that is in the carburetor after the primer bulb has been pushed. The excess fuel is forced through the purge line back into the fuel tank. Over time the Tank Purge Line will become brittle and crack and will need to be replaced.

This Chain Bar Adjuster kit is a kit which contains all necessary hardware for adjusting a chain bar on a chain saw. Installation is rated as "Easy" and requires a screwdriver, wrench set and socket set. This part comes directly from the manufacturer.

The OEM Mounting Bar Nut is a nut used to install a mounting bar to your machine. Installation requires a wrench set and socket set, and is rated as "Easy". This nut attaches to the chainbar studs.

This purge bulb is an authentic OEM part from Craftsman for gas blowers, trimmers, blowers and weed wackers. This part disperses fuel to the carburetor to provide starting the blower faster. You will need a screw driver to replace this part. This purge bulb is made of rubber and sold individually.

This is an OEM replacement part and is sold individually. Its purpose is to filter out dust and debris from contaminating the carburetor and engine. When replacing the filter you can open the package in comes in and put a bit of two cycle oil in the bag and let it absorb into the filter. Then remove it from the bag and squeeze it with a...Read more paper towel to remove the excess oil. This will aid the filter in filtering out the unwantables.

This Bar Pin Adjuster is an OEM part used to adjust the tension on the bar, which loosens or tightens the chain. It attaches to the slot in the bar, and the chainsaw bar adjusting screw. Installation is rated as "Easy" and requires a screwdriver. Refer to your make, model and diagram to ensure this part is correct.

This is a genuine OEM approved replacement starter spring is specially designed for use with gandheld gas powered blowers and trimmers. The purpose of this spring is to retract the starter assembly on the engine, so it engages the drive cup on the flywheel to start the engine when pulled. This spring is made out of metal and it is sold individually.

This metal ring in your engine, known as the piston ring, seals the gap between the piston and cylinder wall. It makes sure that the gases produced during combustion do not escape and that the engine maintains the pressure it needs to run. If the piston ring is damaged, oil can seep into the combustion chamber, causing your engine to exhi...Read morebit rough idling and your machine emit blue smoke. To switch out a defective piston ring, detach the old ring from the piston with a screwdriver. When installing the new ring, you may need to compress it to make it fit properly. Please be aware that this genuine OEM replacement part is bought individually. It is recommended that you replace all the piston rings in your machine at once, as they tend to wear down at the same rate. Carefully review your user manual to determine how many rings your machine needs before placing your order.

This OEM bar adjustment retainer is a metal component that securely holds the adjustment screw and pin in place, allowing you to adjust the chain tension. It is typically located near the front of the chainsaw, close to the guide bar. If the guide bar is over-pressured, the retainer can become stressed and fail, causing it to ride up on t...Read morehe screw. Signs of a damaged retainer include visible breaks or deformations. You may also have trouble in tightening or loosening the chain, as the screw may become loose during adjustment. To remove a faulty retainer, remove the side cover by loosening the nuts and the tension screw on it with a socket. Unscrew the guide bar and replace the damaged retainer. When installing the new retainer, ensure the cone points towards the adjustment pin. Please note that the replacement retainer is sold separately from the guide bar and adjustment pin.

This is a standard hardware which has multiple applications based on your tool. It is sourced from original equipment manufacturer for use with a variety of power equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. Requires a hex key or an allen wrench to install or remove it.