PP220LE Poulan Chainsaw - Parts

This is a genuine part sourced directly from the manufacturer. The Washer-thrust is commonly found in Poulan, Husqvarna and Jonsered chainsaws. The washer is utilized to provide a tight fit between connected parts. It is a high-quality replacement for a damaged or a missing hardware that was installed on a new unit. Refer to the diagrams ...Read morefor your model to ensure the exact location and the correct application of this part. Keep in mind this washer is made of durable metal and is sold as an individual item.

This is a genuine OEM approved starter spring which is specially designed for use with handheld lawn and garden equipment. It is an identical replacement for a missing or a faulty component that was installed on a new unit. The purpose of this spring is to retract the starter assembly on the engine, so it engages the drive cup on the flyw...Read moreheel to start the engine when pulled. This high-quality spring is made of durable metal and is sold individually. Please make sure to check the appropriate diagrams of your model for the correct location and application of this item.

This is an authentic Poulan replacement chain designed for use with chainsaws. It is a key component of a chainsaw which mechanically cuts the material. Over time the chain will stretch, become dull or break. Keep an eye on the condition of the chain and replace as needed. Please note this chain is only for use with 16" bars. Includes one...Read more (1) metal cutting chain per order. The only tool needed for this repair is the scwrench that most likely came with your chainsaw. Otherwise, a flat head screwdriver and a socket wrench will do just fine. • Remove the guide bar side panel • Release the chain tension • Remove the old chain • Loosen the tension screw • Thread the new chain onto the saw • Align the guide bar • Replace the side plate • Tighten the chain to the correct tension • Finish tightening the side plate nuts

This is an authentic replacement part sourced from original manufacturer. It is commonly used on gas chainsaws. A centrifugal clutch is a part that uses centrifugal force to connect two concentric shafts, with the driving shaft nested inside the driven shaft. Today's centrifugal clutches will function even when they shouldn't, far beyond ...Read morethe point of when they need to be replaced. Keeping an eye on equipment performance will determine when the centrifugal clutch requires attention. This clutch is made out of metal and it is sold individually. Please note the clutch drum, spacer and washer are all sold separately. To replace this item you would need a screwdriver and pliers.

It is a genuine isolator assembly that is designed for use with Poulan chainsaws. These parts are supplied by the original equipment manufacturer. The isolator help to reduce vibrations from a working equipment. Over time assembly may wear out and begin to fail and cause the tool to vibrate. Make sure to refer to the appropriate diagrams ...Read moreof your model for the exact location and the correct installation of these parts. Keep in mind this high-quality kit includes three durable metal springs and the hardware to secure them. To perform this repair you will need a screwdriver and a wrench set.

This replacement part is an authentic OEM screw designed for use with gas chainsaws and trimmers. This item is generally used to secure the housing of the equipment. Please refer to diagrams for proper application. This screw is made out of metal and it is sold individually. To secure or loosen this screw you would need a phillips head screwdriver.

This replacement screw is a high quality hardware that is designed for use with Paramount, Poulan and Weed Eater power equipment. It has multiple applications depending on your equipment, please make sure to check appropriate diagrams for correct location and use of this item. One durable hex socket head screw is included per order.

The oil pickup assembly transfers oil between the tank and the oil pump. This is a genuine Poulan and Jonsered replacement part for use in chainsaws. It is made out of rubber with a metal spring. If this part becomes broken it will need to be replaced. A screwdriver and a set of pliers may be needed while replacing this part which is sold individually.

This is a genuine replacement part for Craftsman chainsaws. The bar bolt is designed to sit behind the bar mounting plate and gives a location for the bar to fasten to. The bolt is made from high-quality metal. Note you require two bolts to fasten the bar. This item is sold individually.

This is a genuine OEM sourced replacement screw designed for use with Husqvarna and Poulan chainsaws. This screw has multiple applications depending on the tools model. Please make sure to check appropriate diagrams for correct use and location of this hardware. Keep in mind, this Torx screw is sold individually.

This genuine replacement part is supplied from original equipment manufacturer. It is a commonly used item on chainsaws. This is one of the two bolts used to secure muffler. This is a hex socket head bolt and it is sold individually. You will need a hex key/allen wrench to remove or secure this bolt.

This is an original replacement part manufactured for use with chainsaws and leaf blowers. The washer is commonly used to disperse the pressure put on the flywheel by a nut across a wider surface area. This washer is available as an individual replacement part, please see model diagram for associative parts.