Search repair tips from other customers using simple keywords like "replace", "fit", "remove", "inspect". DIY doesn't mean you have to do it alone!
Search filter:
Clear Filter
Your search term must have 3 or more characters.
burner would not lite
23 of 34 peoplefound this instruction helpful.
Glen from Kenner, LA
Really Easy
Less than 15 mins
Screw drivers
openend stove top disconnected wire pushed out old sparker inserted new one closed lid game over
Was this helpful?
Thank you for voting!
Change bad/broken igniter on gas stove top burners
6 of 6 peoplefound this instruction helpful.
James from Kaplan, LA
Really Easy
Less than 15 mins
Very simple repair with no tools required. Turn off power to stove. Remove grates, remove burner, pull old Top Burner Spark Electrode up being careful not to jerk it up hard - wiggle if necessary, unplug wire from old electrode, plug wire into new electrode making sure it fits snug - if not, squeeze it closed a little at a time until it f
... Read moreits snug, push new igniter into place being careful not to force it and crack the ceramic body. Install burner being careful not to damage the electrode, Install grates. Turn power back on and test to make sure it works. It took me all of 15 minutes to change 2 burner spark electrodes. The only bad thing about this repair is that the shipping costs as much as the parts.
Read less
Was this helpful?
Thank you for voting!
Needed To Replace Burner
5 of 6 peoplefound this instruction helpful.
Robert K from York, PA
Really Easy
Less than 15 mins
Took longer to open the box.
Was this helpful?
Thank you for voting!
Original burner cap was chipping; must have been dropped somewhere along the line.
8 of 15 peoplefound this instruction helpful.
Mitzi from Briarcliff Manor, NY
Really Easy
Less than 15 mins
New burner cap replaced old; just placed over burner; no tools required.
One suggestion: burner cap should have been shipped with thicker bubble protection (easy to do). It was minimally wrapped and placed in a thin, bubble envelope, risking damage in shipping process. Luckily, the burner arrived in tact and usable.
Was this helpful?
Thank you for voting!
Burnt burner
7 of 12 peoplefound this instruction helpful.
Janine from Wind Gap, PA
Really Easy
Less than 15 mins
Just put it on. Quite proud of myself for figuring out what and how to get the part however! The website was very helpful.
Gas range igniter was making a clicking sound every 3 to 5 minutes, as if it was trying to ignite one of the burners.
3 of 3 peoplefound this instruction helpful.
Wesley from FRANKLIN, TN
Really Easy
15 - 30 mins
Pliers
Unplug the range from its wall socket to avoid electric shock. The various range parts that support a pot or frypan are easily lifted off their perches, exposing the small white igniter. The only moderately difficult aspect is wiggling the igniter out of its retainer. The electric wire leading into it then can be pulled out and fed int
... Read moreo the new igniter with a push. Replace igniter in its retainer, then replace the range parts you removed to expose the igniter and plug the range back into the wall socket. Piece of cake.
Read less
Was this helpful?
Thank you for voting!
THE OLD BURNER HEAD WAS NOT TURNING ON PROPERLY AND THE GAS CAME OUT UNEVEN.
Order parts and installed - no tools needed - completed repairs less than 1 minute
Was this helpful?
Thank you for voting!
Large burner cap finish was damaged
3 of 4 peoplefound this instruction helpful.
Richard B from CLARKSBORO, NJ
Very Easy
Less than 15 mins
Just lifted old burner off with my fingers and replaced with the new one. What needs to be focused on here is the fact that Part Select has such a complete line of parts rather than the difficulty in the install.
Was this helpful?
Thank you for voting!
burner had hot spots where the matieral melted some cause a distorted flame that would spit sputter
2 of 2 peoplefound this instruction helpful.
Dan from WARROAD, MN
Really Easy
Less than 15 mins
Nutdriver
Remove the top grate and remove the top burner plate and then pull the burner out and remove the torx screw and adapter install onto the new burner and place back on the stove , good to go.
Was this helpful?
Thank you for voting!
bumper were old and broken
2 of 2 peoplefound this instruction helpful.
Morris from HOUSTON, TX
Really Easy
15 - 30 mins
Screw drivers
Pop old ones out and pressed in the new ones
Was this helpful?
Thank you for voting!
Gas burner wasn’t burning properly
2 of 2 peoplefound this instruction helpful.
Karin from ARUNDEL, ME
Really Easy
Less than 15 mins
I ordered the new burner head and replaced it and now it works perfectly.
Was this helpful?
Thank you for voting!
lens snapped off on the inside-plug was left loose
3 of 6 peoplefound this instruction helpful.
RICKEY from MONTROSE, NY
Easy
Less than 15 mins
Screw drivers
popped out the remainder of old lens, then pushed in new ones and slipped on plugs.
My Orders
