PFS22SISBSS General Electric Refrigerator - Parts

This sensor (Temperature Sensor, Thermistor, Refrigerator Temperature Sensor) sends the temperature reading of the compartment to the control board. If you notice your refrigerator is too warm, too cold, or not defrosting properly, then there may be a problem with your sensor. The temperature sensor can break from material fatigue or thro...Read moreugh normal use, and should be replaced. It is attached to the evaporator and control housing in your appliance. It measures approximately 1.25 inches long with 18 inch wire leads, and is constructed out of plastic. This part comes in white, beige. It includes the sensor, with wire leads.

This 10 by 5 inch ice maker (Electromechanical Icemaker Kit, Ice Maker Assembly) produces ice. This particular model will produce seven crescent shaped cubes every cycle. It is constructed of plastic and metal, and comes in black/white. This kit includes a set of installation instructions, a 4-pin round plug-in connector, 6 post plug-in c...Read moreonnectors, tube and fill cup. The ideal temperature of a freezer is zero degrees Fahrenheit. If the temperature in your freezer is at an appropriate level yet ice is still not being made, it could be an issue with the water inlet valve or your ice maker assembly. If you determine it is the ice maker, this is the replacement you need. The ice maker can break from normal wear and accidental damage. Ice makers will need to be replaced every 3-10 years depending on the frequency of usage and water quality. This model is mounted on the freezer wall.

This electronic board (Main Control Board Assembly, Control Board, Motherboard) controls the temperature and defrost functions of the unit. This control board is located on the back of the refrigerator, and measures 8 inches by 5 inches. It’s constructed of metal and plastic, and comes in green. This kit includes one main control board wi...Read moreth built in defrost controls. If broken due to electrical surges or normal use, your fridge may experience temperatures that are too warm or too cold, or inconsistent defrost cycles. If this happens, the part should be replaced.

Quick connector for plastic water line - 5/16" to 5/16"

This 40-Watt light bulb is sold individually. It is specially designed to withstand extreme temperatures, so this bulb is compatible with a variety of appliance types including refrigerators, ranges, microwaves, and dryers. It features a frosted glass bulb with a standard metal socket base, which allows you to easily unscrew the burnt-out light and twist the new bulb into place.

This part helps the compressor kick on and off while maintaining a constant temperature to keep things frozen in your freezer. This part has been updated by the manufacturer and may appear different than the original, but should function the same.

This OEM filter is sold individually. Change your filter every 6 months for the best results. This filter is found in top-freezer and bottom-freezer refrigerators located in the back upper right corner. It measures 4.75-Inches deep 9.5-Inches high and 5.25-Inches wide. It is certified to reduce particles chlorine-resistant cysts lead and ...Read morefive other impurities. The pressure requirement is 40-120 PSI (if yours exceeds this you?ll need to install a pressure-timing valve) and the operating temperature needs to be 33-100 degrees Fahrenheit. It filters down to 0.5-1 microns. The installation is simple and does not require any tools or mess. To remove the old cartridge turn it to the left and pull down carefully. Some water might drip so keep a cloth handy. To install the new filter place it into the cartridge holder and turn to the right until it will no longer turn. If you have a top-freezer model it should be situated vertically and if it is a bottom-freezer model it should be placed horizontally. Be careful not to over-tighten. If your model has a replacement indicator light reset it by pushing and holding it down for three seconds. If your model has a dispenser run water through it for approximately 3 minutes to clear the system. Please note that this filter will not work in Kenmore brand models.

3 terminal.

This door shelf bin is a genuine OEM replacement part for your refrigerator door. This clear and white plastic bin holds food items on the door of your fridge. It can become cracked or go missing and need replacing. To replace this part, simply pull out the existing door bin, and snap the new one into place using the mounting tabs.

This is the frame only. The glass NOT included.

This is the glass shelf only. The frame can be ordered separately.